LG GM210 Service Manual Download Page 132

Page: 132 / 165

- 133 -

LGE Internal Use Only

10. ENGINEERING MODE

LGE Internal Use Only

10.1.6 ADC (Analog to Digital Converter)

This displays the value of each ADC.

1) MVBAT ADC :

Main Voltage Battery ADC

2) AUX ADC :

Auxiliary ADC

3) TEMPER ADC :

Temperature ADC

10.1.7 BATTERY

1) Bat Cal :

This displays the value of Battery Calibration. The following menus are displayed

in order : BAT_LEV_4V, BAT_LEV_3_LIMIT, BAT_LEV_2_LIMIT,

BAT_LEV_1_LIMIT, BAT_IDLE_LI MIT, BAT_INCALL_LIMIT,

SHUT_DOWN_VOLTAGE, BAT_RECHARGE_LMT

2) TEMP Cal :

This displays the value of Temperature Calibration. The following menus are

displayed in order : TEMP_HIGH_LIMIT, TEMP_HIGH_RECHARGE_LMT,

TEMP_LOW_RECHARGE_LMT, TEMP_LOW_LIMIT

10.1.8 Audio

This is a menu for setting the control register of Voiceband Baseband Codec chip.
Although the actual value can be written over, it returns to default value after switching off
and on the phone.

1) VbControl1

: VbControl1 bit Register Value Setting

2) VbControl2

: VbControl2 bit Register Value Setting

3) VbControl3

: VbControl3 bit Register Value Setting

4) VbControl4

: VbControl4 bit Register Value Setting

5) VbControl5

: VbControl5 bit Register Value Setting

6) VbControl6

: VbControl6 bit Register Value Setting

10.1.9 DAI (Digital Audio Interface)

This menu is to set the Digital Audio Interface Mode for Speech Transcoder and
Acoustic testing.

1) DAI AUDIO

: DAI audio mode

2) DAI UPLINK

: Speech encoder test

3) DAI DOWNLINK

: Speech decoder test

4) DAI OFF

: DAI mode off

Summary of Contents for GM210
































































































































































Search results

Summary of Contents for GM210

Reviews:

LG GM210, Service Manual, Page: 132 / 165

Search results

Summary of Contents for GM210

Reviews: