LG GM210 Service Manual Download Page 24

Page: 24 / 165

- 25 -

LGE Internal Use Only

3. TECHNICAL BRIEF

LGE Internal Use Only

Baseband Analog (VABB)

The Baseband Analog regulator supplies the analog portions of the AD6725. Operation of the VABB

regulator is controlled by the VABBEn bit in the LDOControl1 register.

If VABBEn = 0, the VABB regultor will be disabled unless the AFCDAC is enabled or VCXOEN = 1. If VABBEn

= 1 (the default state) VABB is enabled along with VCORE, VMEM, and VEXT. The Baseband Analog

regulator is optimized for high ripple rejection and low noise. The output of the Baseband Analog

regulator should not be used as a supply for any external components.

Microphone (VMIC)

The Microphone regulator supplies the microphone interface circuitry. The Microphone regulator is

optimized for extremely high ripple rejection up to 217 Hz and low noise.

VRF (VRF)

The VCXO regulator supplies the voltage controlled crystal oscillator (VCXO). The VCXO regulator is

optimized for high ripple rejection and low noise.

USB Interface (VUSB)

The VUSB regulator supplies the USB transceiver located in the DBB. Digital Baseband PLL (VPLL) The

VPLL regulator supplies the phase locked loop on the digital baseband (DBB).

General Purpose Regulator (VGP)

The General Purpose regulator is intended primarily to serve as a supply rail for camera modules. Its

voltage is programmable by setting VGPSel[3:0] in theLDOControl2 Register. VGP is enabled by setting

the VGPEn bit in LDOControl1 to 1.

Applications Regulator (VAPP)

The VAPP regulator is an adjustable regulator that uses an off chip pass device. It has two modes of

operation selected by the state of the VAPPCFG terminal. If VAPPCFG is pulled low the VAPP regulator

functions as a programmable voltage applications supply.

In this mode, VAPP is enabled or disabled using the VAPPEn bit of LDOControl1.

Summary of Contents for GM210
































































































































































Search results

Summary of Contents for GM210

Reviews:

LG GM210, Service Manual, Page: 24 / 165

Search results

Summary of Contents for GM210

Reviews: