LG ARUN040GSS0 Installation Manual Download Page 3 | Manualshive

Page: 3 / 79

background image

3

SAFETY INSTRUCTIONS

ENGLISH

WARNING

• Installation or repairs made by unqualified persons can result in hazards to you and others.

• The information contained in the manual is intended for use by a qualified service technician

familiar with safety procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment

malfunction, property damage, personal injury and/or death.

Installation

• Have all electric work done by a licensed electrician according to "Electric Facility Engineering

Standard" and "Interior Wire Regulations" and the instructions given in this manual and always use a
special circuit.
- If the power source capacity is inadequate or electric work is performed improperly, electric shock

or fire may result.

• Ask the dealer or an authorized technician to install the air conditioner.

- Improper installation by the user may result in water leakage, electric shock, or fire.

• Always ground the product.

- There is risk of fire or electric shock.

• Always install a dedicated circuit and breaker.

- Improper wiring or installation may cause fire or electric shock.

• For re-installation of the installed product, always contact a dealer or an Authorized Service Center.

- There is risk of fire, electric shock, explosion, or injury.

• Do not install, remove, or re-install the unit by yourself (customer).

- There is risk of fire, electric shock, explosion, or injury.

• Do not store or use flammable gas or combustibles near the air conditioner.

- There is risk of fire or failure of product.

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric shock.

• Prepare for strong wind or earthquake and install the unit at the specified place.

- Improper installation may cause the unit to topple and result in injury.
- While installing the product on the rooftop, maintain sufficient distance from the edge to prevent

falling down from the building.

• Do not install the product on a defective installation stand.

- It may cause injury, accident, or damage to the product.

!

WARNING

This indicates that the failure to follow the instructions can cause serious injury or death.

CAUTION

This indicates that the failure to follow the instructions can cause the minor injury or damage to
the product.

This symbol is displayed to indicate matters and operations that can cause risk.
Read the part with this symbol carefully and follow the instructions in order to avoid risk.

!

!

!

SAFETY INSTRUCTIONS

The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe
or incorrect operation of the appliance.
The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described below.

«
1
2
3
4
5
...
»

Summary of Contents for ARUN040GSS0
















































































Reviews:

No comments

Related manuals for ARUN040GSS0

Brand: Daikin Pages: 20

Brand: Panasonic Pages: 108

Brand: Vaillant Pages: 136

Brand: Airwell Pages: 6

Brand: Refinair Pages: 6

Brand: Daikin Pages: 264

Brand: AERMEC Pages: 36

Brand: Livington Pages: 24

Legacy 707C K Series

Brand: Bryant Pages: 30

Brand: Alpic Air Pages: 24

Brand: B.Pro Pages: 24

Brand: HAMPTON BAY Pages: 40

Brand: TCS Pages: 8

Brand: Airwell Pages: 94

Brand: emmeti Pages: 100

Brand: Daikin Pages: 29

DOLCECLIMA BREZZA

Brand: Olimpia splendid Pages: 354

Brand: Fuji Electric Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands