LG ARUN040GSS0 Installation Manual Download Page 63

Page: 63 / 79

ELECTRICAL WIRING

ENGLISH

Automatic Addressing

The address of indoor units would be set by Automatic Addressing

- Wait for 3 minutes after supplying power.

(IDU and ODU should be off.)

- Press RED button of the outdoor units for 5 seconds. (SW01C)

- A “88” is indicated on 7-segment LED of the outdoor unit PCB.

- For completing addressing, 2~7 minutes are required depending on numbers of connected

indoor units.

- Numbers of connected indoor units whose addressing is completed are indicated for

30 seconds on 7-segment LED of the outdoor unit PCB.

- After completing addressing, address of each indoor unit is indicated on the wired remote

control display window. (CH01, CH02, CH03, ……, CH06 : Indicated as numbers of connected
indoor units)

[Heat Pump (MAIN PCB)]

CAUTION

• In replacement of the indoor unit PCB, always perform Automatic addressing setting again.

(At that time, please check about using Independent power module to any indoor unit.)

• If power supply is not applied to the indoor unit, operation error occur.

• Automatic Addressing has to be performed after 3 minutes to improve communication.

DIP-SWITCH

7 - Segment

SW01C (

: confirm)

SW02C (

ඔ

: backward)

SW03C (

ඖ

: forward)

SW04C ( : cancel)

SW01D (reset)

DIP SWITCH

7-Segment

SW01C (

: confirm)

SW02C (

: backward)

SW04C ( X : cancel)

SW01D (reset)

SW03C (

: forward)

(U4)

(U3 / U7)

Summary of Contents for ARUN040GSS0
















































































Search results

Summary of Contents for ARUN040GSS0

Reviews:

Related manuals for ARUN040GSS0

Brands by name

Popular brands

LG ARUN040GSS0, Installation Manual

Search results

Summary of Contents for ARUN040GSS0

Reviews:

Related manuals for ARUN040GSS0

Brands by name

Popular brands