background image

Owner's Manual  7

Safety Precautions

ENGLISH

Do not install the product
where the noise or hot air
from the outdoor unit could
damage the neighborhoods. 

• It may cause a problem for your

neighbors.

Use two or more people to
lift and transport the air
conditioner.  

• Avoid personal injury. 

Do not install the product
where it will be exposed to
sea wind (salt spray)
directly. 

• It may cause corrosion on the

product. Corrosion, particularly on
the condenser and evaporator fins,
could cause product malfunction
or inefficient operation. 

Do not direct airflow at
room occupants. (Don't sit
in the draft.) 

• This could damage your health.

Do not use the product for
special purposes, such as
preserving foods, works of
art, etc. It is a consumer air
conditioner, not a precision
refrigeration system.  

• There is risk of damage or loss

of property.

Do not block the inlet or
outlet of air flow. 

• It may cause product failure.

Use a soft cloth to clean. Do
not use harsh detergents,
solvents, etc.  

• There is risk of fire, electric

shock, or damage to the plastic
parts of the product.

Do not touch the metal
parts of the product when
removing the air filter. They
are very sharp! 

• There is risk of personal injury.

Do not step on or put
anyting on the product.
(outdoor units)  

• There is risk of personal injury

and failure of product.

Operation

Summary of Contents for A182CB NV2































Reviews: