background image

ENGLISH

Owner's Manual  27

Maintenance and Service

Air Intake Vents

Air Outlet Vents

Connecting
Wires

Piping

Drain Hose

Base Plate

Maintenance and Service

Indoor Unit

Outdoor Unit

WARNING: Turn the system off before cleaning. To clean, wipe with a soft, dry cloth.
Do not use bleach or abrasives.

Supply power must be disconnected before cleaning the indoor unit.

Air filter

The air filters behind the front grill should be checked and cleaned once
every 2 weeks or more often if neccessary.
1. Pull up the front panel. After lifting up the filter tab a bit, take the

filter out slowly 

Clean the filter after stopping the product.

2. Clean the filter with a vacuum or warm, soapy water.

• If dirt is conspicuous, wash with a solution of detergent in

lukewarm water.

• If hot water (40°C or more) is used, it may be deformed.

3. After washing with water, dry well in the shade.
4. Re-install the air filter.

Never use any of the followings:
• Water hotter than 40°C.

Could cause deformation and/or discoloration.

• Volatile substances

Could damage the surfaces of the air conditioner.

NOTICE

NOTICE

The heat exchanger coils and panel vents of the outdoor unit should be checked regularly. 
If clogged with dirt or soot, the heat exchanger and panel vents may be professionally steam cleaned.

Dirty or clogged coils will reduce the operating efficiency of the system and cause higher
operating costs.

NOTICE

1

2

Filter

Summary of Contents for A182CB NV2































Reviews: