LG 43LX774H Setup Manual Download Page 37

Page: 37 / 96

206-4309

Installer Menu (Cont.)

069 - EN. CH-T COL. (Enable Display Characters Custom Color)

Set to 1 to enable custom color for MPI display characters. Set to

0 to disable custom color for MPI display characters.

070 - FOR. CH-TIME (Display Characters Foreground Color)

Set the foreground color for MPI display characters according to

the following color chart:
0 = Black

2 = Green

4 = Red

6 = Yellow

1 = Blue

3 = Cyan

5 = Violet

7 = White

If the foreground and background colors for the display characters

are the same, the background will be transparent.

Note:

This item and item 071 BCK. CH-TIME also apply to the

“Channel Not Available” message if item 073 CH NOT AVBLE is

set to 1 (enabled).

Note:

Items 070 FOR. CH-TIME and 071 BCK. CH-TIME are only

available in the Installer Menu when item 069 EN. CH-T COL. is

set to 1.

071 - BCK. CH-TIME (Display Characters Background Color)

See description for item 070 FOR. CH-TIME above. The color

chart is the same for both items.

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL

NOT AVAILABLE” message is displayed when a user attempts to

direct tune a channel that is not included in the channel lineup.

Note:

This item is not available in the Installer Menu when item

028 CH. OVERIDE is set to 1.

Note:

This item is only applicable when the TV is in PTC-CTV

Mode.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of MPI communication occurs, TV automatically

tunes to the specified Start Channel.

Note:

This item is not available in the Installer Menu when item

004 STRT CHANNEL is set to 255.

078 - UPN MSB (UPN Most Significant Byte)

User programmable number, most significant byte readable by

MPI command. Note: Not linked to serial number.

079 - UPN MSB-1 (UPN Most Significant Byte-1)

User programmable number, most significant byte-1 readable by

MPI command. Note: Not linked to serial number.

080 - UPN MSB-2 (UPN Most Significant Byte-2)

User programmable number, most significant byte-2 readable by

MPI command. Note: Not linked to serial number.

081 - UPN LSB (UPN Least Significant Byte)

User programmable number, least significant byte readable by

MPI command. Note: Not linked to serial number.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid MPI checksum validation. Set to 1 for validation.

Set to 0 to disable (does not check checksum on MPI async port).

SPI is always checked.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64 msec,

thus relaxing MPI timing requirements to be compatible with PC-

based Windows controlled systems. Range is 0 - 5.

(Timeout = 25.5MS + [25.5 MS* Handshake time].)

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be permanent

by disabling the blocking hours function. Set to 1 to install Parental

Control restrictions permanently. Set to 0 for user-specified hours

control of blocking schemes.

Note:

This item is not available in the Installer Menu when item

021 V-CHIP is set to 0.

086 - V. MUTE TIME (Video Mute Time)

Use to extend the normal video mute time during channel change.

For example, you may wish to extend the normal video mute time

to prevent the display of encrypted video (i.e., from a Pro:Idiom

encrypted channel) that has not yet been decrypted. When set to

0, the normal video mute time is not extended. Set from 1 to 50 to

increase the normal video mute time in 100 ms step increments up

to a maximum of 5 seconds (e.g., the value of 25 represents 2.5

seconds, or 25 x 100 ms = 2.5 seconds).

088 - EN NOISE MUTE (Enable Noise Mute)

Applicable for analog channels only. If set to 1, audio mutes if no

signal is present.

090 - KEY LOCK

If set to 1, Key Lock is enabled, which means that all display panel

joystick button functions will be locked, i.e., non-functional. Set to

0 to disable Key Lock. Note that all IR features remain functional

regardless of this setting.

091 - HDMI2 ENABLE

Set to 1 to enable HDMI 2 input in DTV Mode. Set to 2 to enable

HDMI 2 input in PC Mode. Set to 0 to disable display panel HDMI

2 input.

092 - HDMI3 ENABLE

Set to 1 to enable HDMI 3 input in DTV Mode. Set to 2 to enable

HDMI 3 input in PC Mode. Set to 0 to disable display panel HDMI

3 input.

Summary of Contents for 43LX774H

































































































Search results

Summary of Contents for 43LX774H

Reviews:

Related manuals for 43LX774H

Brands by name

Popular brands

LG 43LX774H, Setup Manual

Search results

Summary of Contents for 43LX774H

Reviews:

Related manuals for 43LX774H

Brands by name

Popular brands