14
206-4235
EZ-Manager Wizard (Cont.)
EZ-Manager Wizard (Cont.)
Note:
Zoning features are only applicable for TVs that will be configured for FTG Mode via CPU
(using an FTG Configuration [.tlx] file) or for TVs that will be configured via “Teaching” (cloning) using
a USB memory device / .tlx file.
Z
EZ-Manager Wizard
4
3
2
1
Zones, Label, and Room Number
CH
VOL
1 2 3
4 5 6
7 8
0
9
P
A
G
E
Q.MENU
CHAR/NUM
FLASHBK
EXIT
OK
GUIDE
PORTAL
TV
DVD
INPUT
MARK
CC
TIMER
MUTE
INFO
PIP
PIPCH+ PIPCH-
SWAP
PIP INPUT
SAP
MENU
SETTINGS
abc
def
ghi
jkl
mno
pqrs
tuv
wxyz
.,;@
DELETE
1
2
3
4
5
6
7
8
0
9
DEL
CHAR/
NUM
Room Number
TV Zone
0
Label
-----
• If creating Wi-Fi Zones for AP settings, select the appropriate Wi-Fi Zone # (1-99) based on the Wi-Fi Zone in which
this TV is installed.
• If creating Zones for Installer Menu settings and/or Channel Mapping, select the appropriate TV Zone # (0-8)
based on the Zone in which this TV is installed. (See Commercial Mode Setup Guide for more information.)
• Select a Label and/or use the alphanumeric keypad on the remote to input the Room Number.
• When done, select ‘Next’ to continue.
Exit
Next
USB Configuration
Zones & Room Number
Wi-Fi Zone
0
1. Complete the appropriate field(s) as described below. Use the Left/Right arrow keys on the
Installer Remote to navigate between each of the fields.
• Wi-Fi Zone:
Enables you to set a Wi-Fi Zone # so that the TV can be configured with a
particular access point’s login data for wireless networking. Login data (i.e., SSID, security
type, and security key) may be provided in a .tlx file to be used either for Teaching (cloning) or
FTG Mode via CPU configuration. If the Wi-Fi Zone # is left at its default value (0), the TV will
not be configured with login data from a .tlx file.
To assign a Wi-Fi Zone , navigate to the Wi-Fi Zone field at the far left of the screen, and use
the Up/Down arrow keys to specify the desired Wi-Fi Zone # (1–99).
• TV Zone: Enables you to set a TV Zone # so that the TV can be configured with Installer Menu
and/or TV Setup Menu settings intended only for the assigned Zone. The Installer Menu and/
or TV Setup Menu settings may be provided in a .tlx file to be used either for Teaching (cloning)
or FTG Mode via CPU configuration. If the TV is being configured for FTG Mode via CPU, the
TV Zone # setting also allows the TV to omit channels that have been restricted in the FTG
Channel Map.
To change the TV Zone from its default value (0), navigate to the TV Zone field, and use the
Up/Down arrow keys to specify the desired TV Zone # (1–8).
• Label: Allows you to select a North, South, East, or West text label for this TV. In the Label
field, use the Up/Down arrow keys to select the applicable label.
• Room Number: Allows you to specify the number of the room in which the TV is located. In
the Room Number field, you can use the number keys on the Installer Remote to direct enter
a room number. Use the Dash key on the Installer Remote as necessary to toggle between
number and letter characters in the Room Number field. Also, you can use the Flashback key
on the Installer Remote to delete characters in this field.
2. When you are ready to continue, select the appropriate option, as follows:
• To proceed to the next EZ-Manager screen, use the arrow keys to select
Next
, and then
press
OK
on the Installer Remote. Continue to the “Configure Pro:Centric Settings” section
on the following page.
• If you wish to use a USB memory device in conjunction with the TV’s standard USB Down-
load Menu to complete the configuration, continue to “USB Configuration” on pages 17 to 18.
• If you wish to use a USB memory device in conjunction with the LG Smart Install utility to
complete the configuration, see “LG Smart Install Utility” on pages 19 to 20.
