LG 26LT670H Setup Manual Download

Page: 29 / 68

206-4213

USB Cloning Procedures

Learning / Teaching a Master TV Setup using a USB Memory Device / .tlx File

USB Cloning Notes

• Read the IMPORTANT CLONING INFORMATION on page 28 before beginning any cloning procedures.

In particular, ensure that the Master TV Setup does not contain a Channel Map; otherwise, Teaching will

result in the Target TV(s) being configured for FTG Mode via CPU.

• You may edit the filename as part of the Learning procedure; however, a file with edited contents will

not be recognized.

• It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s

clock manually, or use the Auto Clock setting in the TV setup menus.

Learn Setup from Master TV

1.  Ensure the Master TV is set up completely and in Pass-through Mode.
2.  Plug the USB memory device into the USB IN port on the Master TV.
3.  Press

MENU SETTINGS

on the Installer Remote to display the TV

setup menus. Use the arrow navigation keys to select/highlight the

Option

menu icon, and then press the number “

” key a total of seven

times to display the USB Download Menu.

4. To gain access to the “Learn From TV” option in the USB Download

Menu, key in the password used to access the Installer Menu

(Example: Press

5. Use the Up/Down arrow keys to select

Learn From TV

(TLX)

, and then

press

6. To differentiate this .tlx file from others, you can use the Up/Down

arrow keys to change the last five digits of the filename. Press

when

you are ready to initiate Learning.

Learning status will be shown on a progress bar in a new window. When

the Learning process is complete, the USB Download menu will reappear

on the screen.

7. When Learning is done, press on the Installer Remote to exit the

USB Download Menu, and remove the USB memory device from the

Master TV.

Select the file name and press OK to start

xxLT670H-UA00003.TLX

►

UPDATING...

Do not unplug!

25%

USB Download Menu

Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
Teach To TV (TLX)
Learn From TV (TLL)

Learn From TV (TLX)

Learn From TV

Summary of Contents for 26LT670H





































































Search results

Summary of Contents for 26LT670H

Reviews:

Related manuals for 26LT670H

Brands by name

Popular brands

LG 26LT670H, Setup Manual

Search results

Summary of Contents for 26LT670H

Reviews:

Related manuals for 26LT670H

Brands by name

Popular brands