LG-Ericsson LWS Page 31 Installation Manual Download

Page: 31 / 73

Wireless SOHO

Installation and Operation Manual

2.11.1 Registering the GDC-450H / LWS-WK to LWS-BS

Only one Wireless Handset or Keyset can be registered at a time.

2.11.1.1 Enabling Registrations

To enable registration of terminal, the below procedure must be performed on the LWS-BS.

1. Press the

[Menu]

button.

2. Press

[Digit 1]

(CONFIGURATION submenu), or

Select

[1. CONFIGURATION]

using the Navigation up/down key and then press the

[OK]

soft

button or Navigation

„OK‟ key.

3. Press

[Digit 4]

(STATION REGISTRATION submenu), or

Select

[4. STATION REGISTRATION]

using the Navigation up/down key and then press the

[

OK]

soft button or Navigation

„OK‟ key.

4. Press

[Digit 1]

(REGISTER STATION submenu), or

Select

[1. REGISTER STATION]

using the Navigation up/down key and then press the

[OK]

soft button or Navigation

„OK‟ key.

5. Select the phone type using the Navigation left/right key (GDC-4XX or LWS-WK)
6.

Press the Navigation

[OK]

button or

[OK]

soft key

7. Proceed to instructions below -

“Registering GDC-450H to the LWS-BS” or “Registering LWS-

WK to the LWS-BS.

8. When the registration is completed, the below message is shown on the LCD of the LWS-BS.

STATION: 10X
SUBSCRIBED: SUCCESS

2.11.1.2 Registering GDC-450H to the LWS-BS

To register to the LWS-BS, the below procedure must be performed on the GDC-450H.

1. Press the

[Menu]

( ) button to display the menu.

2. Highlight [Phone Register] in the menu using the

Navigation

( ) button.

3. Press the

[OK]

( ) button; and then the Phone Register menu will display.

4. Select

[LWS Subscription]

using the up and down arrows of the

Navigation

( ) button

and press the

[OK]

( ) button.

5. Display

[Searching.1]

6. The system

[RFPI] (e.g. 01234567890123)

will display when a system is found.

The RFPI of your system is available from your System Administrator, or perhaps the attend-
ant.

7. Press the

[OK]

( ) button; in a few seconds, a confirmation tone will be heard at the

GDC-450H.

8. If the registration fails, repeat the procedure from Step 1 to 7 at the LWS-BS and Step 1 to

7 from the GDC-450H.



: [Menu], [OK] button on GDC-450H



RFPI : Radio Fixed Part Identity



Seven Wireless Handsets and/or Keysets can be registered to one LWS-BS.

Note:

Summary of Contents for LWS










































































Search results

Summary of Contents for LWS

Reviews:

Related manuals for LWS

Brands by name

Popular brands

LG-Ericsson LWS, Installation Manual

Search results

Summary of Contents for LWS

Reviews:

Related manuals for LWS

Brands by name

Popular brands