manualshive.com logo in svg

LG Chem RESU Series, Installation Manual

Share
Download
LG Chem RESU Series Installation Manual Download Page 29

4

Commissioning

4.1

LED indicators

ON

OFF

CO

NNECTIO

N KI

T

The LED indicators on the front of the battery pack show its operating state:

ON

: This indicator is lit when the circuit breaker switch is in the

ON

position.

Charging

: This indicator is lit while the battery pack is charging.

Discharging

: This indicator is lit while the battery pack is discharging.

Warning

: This indicator is lit when the battery pack is in a warning state. See

Troubleshooting

on page 31.

4.2

Starting the battery pack

Put the battery pack in operation by taking these steps:

1. Move the circuit breaker switch to the

ON

position to turn on the battery

pack.

2. Make sure that the

ON

indicator is lit. If it stays off, do not use the battery

pack. Contact LG Chem or your distributor.

3. Turn on the inverter.

NOTE

If communication with the inverter is not established within 10 minutes
after the battery pack is turned on, the circuit breaker automatically trips.

29

Summary of Contents for RESU Series






































Reviews:

No comments

Brands by name

Popular brands

Load more brands