Lexmark Z51 Color Jetprinter Service Manual Download Page 41 | Manualshive

Page: 41 / 70

background image

Repair Information

4-7

4098-001

Paper Feed Motor Removal

1. Remove all covers.

2. Remove the sheet feeder.

3. Disconnect (J12) the paper feed motor from the system board.

4. Remove the two screws mounting the paper feed motor and

remove the motor. Note the routing of all cables.

Power / Parallel / USB Board Removal

1. Remove all covers.

2. Disconnect the system board cable.

3. Remove two screws and disconnect two ground wires.

4. Depress latches and slide the card out.

Printhead Carrier Assembly / Shaft Removal

1. Remove all covers.

2. Apply pressure to the idler pulley and remove the belt from the

transport carrier motor.

3. Remove the retainers from the ends of the carrier shaft.

4. Slide the shaft left and remove from the printer.

5. Disconnect printhead cables from the system board.

Note: The carrier is attached to the belt at a raised tab. When
reinstalling, be sure the belt tab and carrier are aligned.

6. Remove the carrier belt from the rear of the carrier.

7. Remove the carrier.

«
...
39
40
41
42
43
...
»

Summary of Contents for Z51 Color Jetprinter







































































Reviews:

No comments

Related manuals for Z51 Color Jetprinter

Brand: Ier Pages: 8

Brand: DataCard Pages: 8

Brand: DataCard Pages: 8

Brand: DataCard Pages: 3

M-Class Mark II

Brand: Datamax Pages: 94

VarioPrint 6000 MICR series

Brand: Oce Pages: 264

Brand: Oce Pages: 194

Brand: Unimark Pages: 38

Brand: Panasonic Pages: 240

Brand: Oki Pages: 98

Brand: Lexmark Pages: 11

Brand: Posnet Pages: 2

Brand: Ricoh Pages: 17

Brand: Oki Pages: 57

Brand: Konica Minolta Pages: 84

Brand: Xerox Pages: 4

Brand: Mayku Pages: 2

ECOSYS M3860idn

Brand: Kyocera Pages: 483

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands