manualshive.com logo in svg

Lexmark X295, Service Manual

Share
Download
Lexmark X295 Service Manual Download Page 132

2-94

  Service Manual

7541-03x

Go Back

Previous

Next

Hard disk option

Service Tip: The 5041-030 printers support one hard disk option. Be sure only one hard disk option is installed. 
Be sure the hard disk and the hard disk board are correctly installed. Run the 

“Quick Disk Test” on page 3-23

 

from the Device Test on the Diagnostic Menu. 

Note:  

The Quick Disk Test is a non-destructive test and indicates Pass or Fail. If the test fails, replace the 

hard disk. If a problem still exists, replace the RIP board.

Use the 

“Disk Test/Clean” on page 3-23

 to help restore the disk if it contains bad data and is unusable. This 

test is divided into a cleaning and a verifying or testing section.

Warning:  

This can be a very lengthy test depending on the disk size. This test leaves the hard disk 

unformatted. The servicer or user must reformat the disk using the Format Disk Menu operation. This is a 
destructive type of test. All the data on the disk is destroyed and should not be performed on a known good 
disk.

Network card option

The network is installed on the system board on network model printers. See 

“Networking service check” on 

page 2-87

Error code 976 - Network card x

A 976 error code indicates an unrecoverable software error in network card x. Verify that network card x is 
correctly installed and all the IPSP cables are properly connected. If you find no problem, contact your next level 
of support before replacing the network card.

54 Network <x> Software error

This error displays when the RIP software detects that a network card is installed in slot x on the interconnect 
board but cannot establish communications with the network card.

Summary of Contents for X295





















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands