Lexmark CS921 User Manual Download Page 35

Page: 35 / 169

Cleaning printer parts

Cleaning the printer

CAUTION—SHOCK HAZARD:

To avoid the risk of electrical shock when cleaning the exterior of the

printer, unplug the power cord from the electrical outlet and disconnect all cables from the printer before
proceeding.

Notes:

•

Perform this task after every few months.

•

Damage to the printer caused by improper handling is not covered by the printer warranty.

Turn off the printer, and then unplug the power cord from the electrical outlet.

Remove paper from the standard bin and multipurpose feeder.

Remove any dust, lint, and pieces of paper around the printer using a soft brush or vacuum.

Wipe the outside of the printer with a damp, soft, lint

‑

free cloth.

Notes:

•

Do not use household cleaners or detergents, as they may damage the ﬁnish of the printer.

•

Make sure that all areas of the printer are dry after cleaning.

Connect the power cord to the electrical outlet, and then turn on the printer.

CAUTION—POTENTIAL INJURY:

To avoid the risk of ﬁre or electrical shock, connect the power cord

to an appropriately rated and properly grounded electrical outlet that is near the product and easily
accessible.

Maintaining the printer

Summary of Contents for CS921










































































































































































Search results

Summary of Contents for CS921

Reviews:

Related manuals for CS921

Brands by name

Popular brands

Lexmark CS921, User Manual

Search results

Summary of Contents for CS921

Reviews:

Related manuals for CS921

Brands by name

Popular brands