Leviton Topaz 24 Installation & Maintenance Manual Download

Page: 2 / 14

Table of Contents

Unpack rack(s)………………………………………………………………….. 1

Mount rack(s)…………………………………………………………………… 1

Terminate conduits…………………………………………………………….. 3

Convert bussing to single-phase………………………………………….…. 3

Pull power, load and control conductors to the racks……………………… 3

Connect power feeders………………………………………………………... 4

Label circuits……………………………………………………………………. 4

Connect load conductors……………………………………………………… 5

Low-voltage application notes………………………………………………… 5

Connect control conductors…………………………………………………… 6

Seal unused openings…………………………………………………………. 6

Install control module(s)……………………………………………………….. 7

Set thumbwheel switch(es)……………………………………………………. 8

Set non-dim switches………………………………………………………….. 8

Apply power and check………………………………………………………... 9

Install dimmers………………………………………………………………….. 9

Install filler modules………………………….…………………..……………. 9

Test loads……………………………………………………………………….. 9

Close door………………………………………………………………………. 10

Maintenance and Specifications ……………………………………………... 11

Warranty ………………………………………………………………………… 12

Summary of Contents for Topaz 24















Search results

Summary of Contents for Topaz 24

Reviews:

Related manuals for Topaz 24

Brands by name

Popular brands

Leviton Topaz 24, Installation & Maintenance Manual

Search results

Summary of Contents for Topaz 24

Reviews:

Related manuals for Topaz 24

Brands by name

Popular brands