background image

 
LEVITON-NSI DIVISION TWO-YEAR LIMITED WARRANTY 

 
Leviton-NSI warrants new Leviton-NSI electronic control and dimmer products to be free from defective materials and 
workmanship for a period of two years from the date of purchase to the original owner when purchased from an 
authorized Leviton-NSI dealer. 
 
Fixtures, lamps and gel material are not covered under this warranty. 
 
The purchaser is encouraged to complete and mail to Leviton-NSI the product registration card enclosed with each 
product.  Leviton-NSI products that have been subjected to accident, alteration, abuse or defacing of the serial number 
are not covered by this warranty.  The normal wear and tear of items such as knobs, jacks and switches are not covered 
under this warranty. 
 
If your Leviton-NSI product requires service during the warranty period, Leviton-NSI will repair, at its option, defective 
materials provided you have identified yourself as the original owner of the product to Leviton-NSI or any authorized 
Leviton-NSI dealer.  Transportation charges to and from an authorized dealer or the Leviton-NSI factory for repair shall be 
the responsibility of the owner.  All products returned to Leviton-NSI must have a factory return authorization number 
issued prior to shipping. 
 
Leviton-NSI is not liable for any incidental or consequential damages resulting from defect or failure other than repairs of 
the Leviton-NSI product subject to the terms of this warranty.  This warranty gives you specific legal rights, and you may 
have other rights which vary from state to state. This warranty is expressly in lieu of all other agreements and warranties 
expressed or implied except as may be otherwise required by law. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

20497 SW Teton Avenue 
Tualatin, OR 97062 
503-404-5500 
fax: 503-404-5600 
 
 

Page 12

 

Summary of Contents for Topaz 24















Reviews: