LevelOne FCS-5030 User Manual Download Page 57

Page: 57 / 114

RTP plus 1.
User can modify Multicast setting for stream1 and stream2.

“Always multicast”

Select it to enable multicast always.

“Multicast group address”

It is used by sources and the receivers to send and receive content.

“Multicast video port”

The video channel port for multicast. It must be an even number.

“Multicast RTCP video port”

The video channel port for multicast RTCP. It must be the port

number of multicast video port plus 1.

“Multicast audio port”

The audio channel port for multicast. It must be an even number.

“Multicast RTCP audio port”

The audio channel port for multicast RTCP. It must be the port

number of multicast audio port plus 1.

“Multicast TTL”

It specifies the number of routers (hops) that multicast traffic is permitted to pass

through before expiring on the network.

Summary of Contents for FCS-5030



















































































































Search results

Summary of Contents for FCS-5030

Reviews:

Related manuals for FCS-5030

Brands by name

Popular brands

LevelOne FCS-5030, User Manual

Search results

Summary of Contents for FCS-5030

Reviews:

Related manuals for FCS-5030

Brands by name

Popular brands