manualshive.com logo in svg

Leuze electronic LSIS 222, Technical Description, Page: 36 / 95

Share
Download
Leuze electronic LSIS 222 Technical Description Download Page 36

Configuration using configuration codes

34

Technical description LSIS 22x

Leuze electronic

7.2

Configuration of the reading gate control (trigger)

Multiple trigger modes are available for controlling the reading gate (start/stop reading):

•

Manual/serial trigger mode 
(factory setting for RS 232 and USB COM port)

With manual/serial trigger mode, the reading gate opens if the trigger button is 
pressed, the trigger input is activated by applying a high signal, or if the 

<SYN>T<CR> read start command

 is sent to the LSIS 22x via the serial interface. 

The reading gate closes if a code is read successfully, the trigger button released, 
the trigger input deactivated by removing the high signal, or if the 

<SYN>U<CR> 

read stop command

 is sent to the LSIS 22x via the serial interface. 

With serial trigger (trigger commands via the serial interface), a 

read time-out

 time 

can 

optionally

 be set, after which the reading gate is closed if no code was read.

•

Presentation mode

In presentation mode, the LSIS 22x is set to 

permanent reading

 for ambient light. 

The reading gate is continuously open. If a change in the image area is detected, the 
LSIS 22x first tries to read a code. If this is not successful, the intensity of the LED 
illumination is continuously increased until a code is read. Following the successful 
reading of a code, the LED illumination is switched off again after a few seconds.

•

Streaming presentation mode 
(factory setting for USB keyboard emulation)

In streaming presentation mode, the LSIS 22x is set to 

permanent reading

 with per-

manently switched-on LED illumination. The reading gate is continuously open.

Normal / enhanced mode

With 

manual/serial trigger mode

 and with 

streaming presentation mode

, a distinction

is also made between the 

normal

 and 

enhanced

 settings:

• The 

normal

 setting (factory setting) offers good reading speed at maximum operat-

ing range.

• The 

enhanced

 setting, on the other hand, offers maximum reading speed at a 

slightly reduced operating range.

Notice!

If in doubt, test which setting, 

normal

 or 

enhanced

, delivers the best results in your appli-

cation.

Summary of Contents for LSIS 222
































































































Reviews:

No comments