background image

 

 

 

OVERVIEW

 

 

PoE and Non-PoE are both highly utilized in industrial networking applications nowadays; however, it 
sometimes goes to an awkward situation that end-device, e.g. remote camera, supports PoE function but 
the Ethernet switch does not. Is there any other solution but replacing the switch with a PoE one? 
 
GINJ-0201-BT-12

 

Series solve the problem simply by deploying data and power from non-PoE switch and 

power input to the PD device. PoE injector is a brilliant low-cost solution for the case that only one side of 
the device is supporting PoE function. Therefore GINJ-0201-BT-12 Series will be your best choice to deal 
with the lack of PoE function cases. 
 
Additionally, GINJ-0201-BT-12 Series supports power input from 9VDC to 55VDC

 

with power booster 

technology, ensuring full 90W PoE output, in compliance with IEEE 802.3bt standard for better usage in 
various industrial markets, like automation, surveillance, and vehicle industry. Besides that, with the fan-
less design, this model series also works perfectly in polarized temperatures from -40~75

 and 

undoubtedly becomes your best option in a harsh environment. 

 

Key Features 

Interface & Performance 

 

Embedded 1*10/100/1000Tx for LAN-In and 1*10/100/1000Tx for BT PoE P.S.E. Out 

 

Compliant with IEEE802.3af/at/bt PoE technologies 

 

Support auto detection and classification for PoE application 

 

Support short-circuit and current-overloading protection for PoE application 

 

Provided power booster technologies for low voltage power inputs 

Power Input 

 

GINJ-0201-BT-12-T: Dual 9-55VDC redundant power inputs 

 

1*4-pin removable terminal block  

 

Max. current 8A (Included PoE power budget) 

 

Max. PoE output: 60W@9V, 90W@12-55VDC  

Certification 

 

CE/FCC 

Operating Temperature 

 

Operating temperature model: -40°C ~ 75°C 

Case/Installation 

 

IP30 protection (not certified by UL) 

 

DIN-Rail and wall mount design 

 

Installation in a pollution degree 2 industrial environment 

 

Installation in the environment with adequate airflow

Summary of Contents for GINJ-0201-BT



















Reviews: