background image

 

 

 

 

Caution:

 If the equipment is used in a manner not specified by the manufacturer, the 

protection provided by the equipment may be impaired.

 

 

Attention: 

Si l'équipement est utilisé d'une manière non spécifiée par le fabricant, la 

protection fournie par l'équipement peut être altérée.

 

 

 

 

Caution:

 The installation that the safety to any system incorporating the equipment is 

the responsibility of the assembler of the system.

 

 

Attention: 

L'installation que la sécurité de tout système intégrant l'équipement est de la 

responsabilité de l'assembleur du système.

 

 

 

 

Caution:

 This is an OPEN TYPE module and should be installed in a final safety enclosure 

characteristic.

 

 

Attention: 

Il s'agit d'un module de TYPE OUVERT et doit être installé dans une 

caractéristique finale d'enceinte de sécurité.

 

 

 

 

Caution:

 This device is intended for use indoor and at altitudes up to 2000 meters. 

 

 

Attention: 

Cet appareil est destiné à être utilisé en intérieur et à des altitudes allant 

jusqu'à 2000 mètres. 

 

 

 

 

Caution:

 Ambient Relative Humidity should be within the range of 5 and 95% (non-

condensing).

 

 

Attention: 

L'humidité relative ambiante doit être comprise entre 5 et 95% (sans 

condensation).

 

 

Summary of Contents for GINJ-0201-BT



















Reviews: