background image

Silver Locomotive decoder

 

13

 

 

 

North American Warranty

 

Lenz GmbH does everything it can do to ensure that its products are free from defects and will 
operate for the life of your model railroad equipment.  From time to time even the best engineered 
products fail either due to a faulty part or from accidental mistakes in installation.  To protect your 
investment in Digital plus products, Lenz GmbH offers a very aggressive 10 year Limited 
Warranty.  

This warranty is not valid if the user has altered, intentionally misused the Digital Plus product, or 
removed the product's protection, for example the heat shrink from decoders and other devices.  
In this case a service charge will be applied for all repairs or replacements. Should the user 
desire to alter a Digital Plus Product, they should contact Lenz GmbH for prior authorization.  

Year One:

  A full repair or replacement will be provided to the original purchaser for any item that 

that has failed due to manufacturer defects or failures caused by accidental user installation 
problems.  Should the item no longer be produced and the item is not repairable, a similar item 
will be substituted at the manufacturer’s discretion.  The user must pay for shipping to an 
authorized Lenz GmbH warranty center.  

Year 2 and 3:

  A full replacement for any item will be provided that has failed due to manufacturer 

defects.  If the failure was caused by accidental user installation or use, a minimal service charge 
may be imposed.  Should the item no longer be produced and the item is not repairable, a similar 
item will be substituted at the manufacturer’s discretion.  The user must pay shipping to and from 
the authorized Lenz GmbH warranty center during this portion of the warranty period.  

Year 4-10:

  A minimal service charge will be placed on each item that has failed due to 

manufacturer defects and/or accidental user installation problems.  Should the item no longer be 
produced and the item is not repairable, a similar item will be substituted at the manufacturer’s 
discretion.  The user must pay shipping to and from the authorized Lenz GmbH warranty center 
during this portion of the warranty period. 

Please contact your dealer or authorized Lenz GmbH warranty center for specific instructions and 
current service charges prior to returning any equipment for repair.

 

 

Hüttenbergstraße 29 

35398 Gießen, Germany 

Hotline: 06403 900 133 

Fax: 06403 900155 

[email protected] 

http://www.lenz.com

 

Lenz Agency of North America 

PO Box 143 

Chelmsford, MA 01824 

ph: 978 250 1494 

fax: 978 455 LENZ 
[email protected] 

This equipment complies with Part 15 of FCC Rules.  Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 

 Please save this manual for future reference!

 

© 2005 Lenz GmbH,  All Rights Reserved

 

Summary of Contents for Digital plus Silver 10331














Reviews: