Lenovo thinksystem SN850 7X15 Setup Manual Download Page 58

Page: 58 / 88

Figure 33. Pressing the foam

Step 7. Route cable back into the cable clip if the cable was removed earlier.

Figure 34. Routing the cable back into clip

After you install the RAID adapter, complete the following steps:

1. Install any removed storage drives and hard disk drive bay fillers (see “Install a 2.5-inch hot-swap drive”

on page 32).

Note:

Install storage drives in the same bay locations as from which they were removed.

2. Configure the RAID array after power on the compute node (see “RAID configuration” on page 65).

Install the flash power module

Use this information to install the flash power module.

ThinkSystem SN850 Compute Node Setup Guide

Summary of Contents for thinksystem SN850 7X15

























































































Search results

Summary of Contents for thinksystem SN850 7X15

Reviews:

Related manuals for thinksystem SN850 7X15

Brands by name

Popular brands

Lenovo thinksystem SN850 7X15, Setup Manual

Search results

Summary of Contents for thinksystem SN850 7X15

Reviews:

Related manuals for thinksystem SN850 7X15

Brands by name

Popular brands