Lenovo ThinkCentre M53 Hardware Maintenance Manual Download Page 138

Page: 138 / 184

Installing or replacing the cover presence switch

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

Note:

The cover presence switch is only available in some models.

To install or replace the cover presence switch, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 123.

3. If you are replacing the cover presence switch, disconnect the cover-presence-switch cable from the

system board. Then, lift the cover presence switch out of the holder.

Figure 44. Removing the cover presence switch

4. Insert the new cover presence switch into place as shown.

Figure 45. Installing the cover presence switch

5. Connect the cable of the new cover presence switch to the cover-presence-switch connector on the

system board. See “Locating parts on the system board” on page 34.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

130

ThinkCentre M53 Hardware Maintenance Manual

Summary of Contents for ThinkCentre M53
























































































































































































Search results

Summary of Contents for ThinkCentre M53

Reviews:

Related manuals for ThinkCentre M53

Brands by name

Popular brands

Lenovo ThinkCentre M53, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre M53

Reviews:

Related manuals for ThinkCentre M53

Brands by name

Popular brands