manualshive.com logo in svg

Lenovo 70LU, User Manual And Hardware Maintenance Manual

Share
Download
Lenovo 70LU User Manual And Hardware Maintenance Manual Download Page 97

®

Figure 81. Installing the intrusion switch

4.  Connect the intrusion switch cable to the intrusion switch connector on the system board. See “System 

board components” on page 19.

Power supply assembly

Your server supports one of the following power supply configurations: 

•  250-watt non-hot-swap power supply (80 PLUS Bronze)

•  400-watt non-hot-swap power supply (80 PLUS Platinum)

Note:

To support a discrete graphic adapter, you must select the 400-watt non-hot-swap power supply.

•  “Removing the power supply assembly” on page 86

•  “Installing the power supply assembly” on page 86

Although there are no moving parts in your server after the power cord has been disconnected, the following 
warnings are required for your safety and proper Underwriters Laboratories (UL) certification.

DANGER

Hazardous moving parts. Keep fingers and other body parts away.

CAUTION: 
Never remove the cover on a power supply or any part that has the following label attached.  

Chapter 5

.

Replacing hardware

85

Summary of Contents for 70LU















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands