manualshive.com logo in svg

Lenovo 10AS, User Manual, Page: 114 / 148

Share
Download
Lenovo 10AS User Manual Download Page 114

Note:

For detailed information on how to open Control Panel on Windows 8 and Windows 8.1, see

“Accessing Lenovo programs on the Windows 8 or Windows 8.1 operating system” on page 6.

2. Click

Hardware and Sound

.

3. Click

Device Manager

. If you are prompted for an administrator password or confirmation, type the

password or provide confirmation.

4. If an exclamation mark is displayed next to an adapter name under

Network adapters

, you might

not be using the correct driver or the driver is not enabled. To update the driver, right-click the
highlighted adapter.

5. Click

Update Driver Software

, and then follow the instructions on the screen.

• The switch port and the adapter have the same duplex setting.

If you configured the adapter for full duplex, ensure that the switch port is also configured for full duplex.
Setting the wrong duplex mode can degrade performance, cause data loss, or result in lost connections.

• You have installed all networking software that is necessary for your network environment.

Check with your LAN administrator for the necessary networking software.

The adapter stops working for no apparent reason

Symptom: The adapter stops working for no apparent reason.

Action: The network driver files may be corrupt or missing. Update the driver by referring to the “Solution”
description for the procedure to make sure that the correct device driver is installed.

The Wake on LAN feature is not working

Symptom: The Wake on LAN (WOL) feature is not working.

Actions:

• Make sure that WOL is enabled in the BIOS Setup Utility program.

• If it is, check with your LAN administrator for the necessary settings.

If your computer is a Gigabit Ethernet model and you use a speed of 1000 Mbps, the connection
fails or errors occur

Symptom: If your computer is a Gigabit Ethernet model and you use a speed of 1000 Mbps, the connection
fails or errors occur.

Actions:

• Use Category 5 wiring and make sure that the network cable is securely connected.

• Connect to a 1000 BASE-T hub/switch (not 1000 BASE-X).

If your computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps. Instead,
it connects at 100 Mbps

Symptom: If your computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps.
Instead, it connects at 100 Mbps.

Actions:

• Try another cable.

• Make sure that the link partner is set to auto-negotiate.

• Make sure that the switch is 802.3ab-compliant (gigabit over copper).

102

ThinkCentre E73 User Guide

Summary of Contents for 10AS





















































































































































Reviews:

No comments