background image

20

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

FUEL

This unit is designed and engineered to burn, dry, well-seasoned wood only.

Dry, seasoned wood is that which has been cut, split and allowed to dry 

under a covered area where air is free to flow and circulate under and 

around the wood (not under a tarp or plastic). Make sure wood is not 

stacked directly on the ground, it may absorb moisture from the ground. 

It should be allowed to dry in these conditions for a minimum of six 

months, preferably one year or more.

 

IT MUST BE UNDERSTOOD 

THAT WOOD CANNOT BE LEFT IN ANY KIND OF WET OR DAMP 

AREA OR IT WILL NEVER BECOME COMPLETELY SEASONED.

Your stove will not operate at the level that it is meant to unless you use 

seasoned, dry wood. Do not burn driftwood or wood that has been in salt 

water, doing so will void your warranty. Do not burn treated wood, coal, 

garbage, cardboard, solvents, or colored paper. Burning treated wood, 

garbage, solvents, or colored paper may result in the release of toxic 

fumes. This type of burning will also void your warranty.

Do Not store fuel within space heater installation clearances or within 

the space required for refueling and ash removal.

Figure 26

Figure 25

Figure 27

OK

5.  Once kindling is burning well, larger pieces of wood may be added, 

then the door should be fully closed if there was the need to keep it 

slightly open during start up.

6.  For best results, use smaller pieces of wood to get the stove tem-

perature very high before loading larger wood for sustained burns. 

If  necessary,  crack  the  door  to  allow  ignition  of  the  fuel  charge. 

Now you can add larger pieces of wood and after several minutes of 

high burn, set the left control for the desired heat output. Check the 

exhaust in about 15 to 20 minutes 

(see 

Figure 26

)

. Large amounts 

of smoke indicate an improper burn setting (either too high or too 

low). Adjust and recheck in 5 to 10 minutes.

4' 

4' 

8' 

Standard 

Cord of

Wood

What does “Well-Seasoned” mean?

When a tree is cut down, the wood is green, full of sap and moisture. 

This moisture content can exceed 80%, which must be reduced to less 

than 20%. Wood properly seasoned is then capable of generating the 

heat the stove was designed to provide.

Green wood does not burn easily.  Attempting to burn green wood often 

results in a lot of smoke and very little fire. Time is the most important 

factor in seasoning wood.  Ideally the moisture content should be reduced 

to 11-20%.  NOTE: The use of a firewood moisture meter is recommended 

to ensure the firewood contains less than 20% moisture.

Seasoning Guide

Softwoods – 6 months to 18 months

Hardwoods – 12 months to 24 months

Logs that are 5” diameter across or larger should be split in half, three 

pieces if over 8 inches, and four pieces when over a foot across.  If a tree 

has been dead for 2 – 4 years it still needs to be cut, split, and seasoned 

for 6 to 24 months depending on the wood.

8 Ft. 

(2.4M)

4 Ft. 

(1.2M)

4 Ft. (1.2M)

Summary of Contents for Grandview GV 230































Reviews: