13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Pl
an
ni
ng
In
st
al
la
tio
n
Sa
fe
ty
a
nd
G
en
er
al
In
st
al
la
tio
n
Op
er
at
io
n
M
ai
nt
en
an
ce
Tr
ou
bl
es
ho
ot
in
g
Pa
rts
/
Ac
ce
ss
or
ie
s
Figure 10
Residential and Mobile Homes
(Tieing down and grounding are required only in mobile homes)
Open all cartons, if any and remove the contents upon receipt and check
for any damaged or missing parts. If there is hidden damage, notify your
freight company or Lennox Hearth Products dealer immediately.
CAUTION: Wear gloves during installation in case of sharp
edges on the stove.
Leg Installation
1. Carefully place stove on it’s back. Be careful not to scratch the stove,
use a piece of cardboard or carpet to protect the back of the stove.
2. Using a 9/16” wrench or socket remove the bolt in each of the four
corners along with the attached shipping brackets.
3. Remove legs from the packaging and using the bolts and washers
that come with the legs install each leg in each corner with one bolt
and one washer.
4. Before the legs are fully tightened down make sure that they are aligned
correctly to match the front and side planes of the stove.
5. The stove can now be set up on the legs making sure that all baffle
boards and bricks are set back in place. These items may have shifted
when the stove was placed on it’s back.
6. If it is necessary to level, secure, or ground your stove, use the holes
in the bottom of the leg for those applications. To level the stove use
leg leveling kit (P/N H8407) or leveling pads (P/N H7638). Level by
adjusting the bolt or leveling pad down on each leg that is not in full
contact with the hearth or surface below that the stove in located on.
LEG INSTALLATION
Figure 11
PEDESTAL INSTALLATION
Residential and Mobile Homes
(Tieing down and grounding are required only in mobile homes)
Open all cartons, if any and remove the contents upon receipt and check
for any damaged or missing parts. If there is hidden damage, notify your
freight company or Lennox Hearth Products dealer immediately.
CAUTION: Wear gloves during installation in case of sharp
edges on the stove.
Pedestal Installation
1. Remove the heater from the carton, if packaged, upon receipt and
check for any damaged or missing parts.
2. Install the 10-24 screws included with the pedestal kit to the bottom
of the stove as seen in Figure 11. You will need a 5/32” allen wrench
to complete this.
3. Carefully place stove on it’s back. Be careful not to scratch the stove,
use a piece of cardboard or carpet to protect the back of the stove.
4. The pedestal will have key hole slots that line up with the screws that
were placed in the bottom of the stove. Carefully install pedestal on
the installed screws with the open end of the pedestal towards the
rear of the stove.
5. Assuring that the pedestal is placed correctly in slots then tighten all
six screws.
6. The stove can now be set up on the pedestal making sure that all
baffle boards and bricks are set back in place. These items may have
shifted when the stove was placed on it’s back.
7. When installing a pedestal on this stove you MUST plug the one leg
mounting bolt hole, located on the bottom of the stove in the front left
corner, with the bolt that was used to mount the shipping legs.
FAIL-
URE TO INSTALL THIS BOLT PROPERLY WILL RESULT IN REDUCED
CONTROL OF THE STOVE’S COMBUSTION SYSTEM!
In
st
al
la
tio
n
Pl
an
ni
ng
In
st
al
la
tio
n
You MUST plug
this one leg
mounting bolt
hole. Read Step
7 above.