background image

Page 1

Corp. 1503-L7

EL16XC1

Service Literature

INSTALLATION AND SERVICE PROCEDURE

August 29, 2016

EL16XC1 (HFC-410A) SERIES UNITS WITH ALL-ALUMINUM COIL

This literature is intended as a general guide and does not
supersede local codes in any way. Consult authorities who
have jurisdiction before installation.

WARNING

Improper installation, adjustment, alteration, service or
maintenance can cause personal injury, loss of life, or
damage to property.

Installation and service must be performed by a licensed
professional installer (or equivalent) or a service agency.

 

IMPORTANT

This unit must be matched with an indoor coil as speci­
fied in 

Lennox EL16XC1

 E

ngineering Handbook

. Coils

previously charged with HCFC-22 must be flushed.

WARNING

Electric Shock Hazard. Can cause injury
or death. Unit must be grounded in
accordance with national and local
codes.

Line voltage is present at all
components when unit is not in
operation on units with single‐pole
contactors. Disconnect all remote
electric power supplies before opening
access panel. Unit may have multiple
power supplies.

TABLE OF CONTENTS

Model Number Identification

2

. . . . . . . . . . . . . . . . . . . .

Typical Serial Number Identification

2

. . . . . . . . . . . . . .

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical Data

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unit Dimensions

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unit Parts Arrangement

5

. . . . . . . . . . . . . . . . . . . . . . . .

Operating Gauge Set and Service Valves

6

. . . . . . . . .

Outdoor Unit Placement

8

. . . . . . . . . . . . . . . . . . . . . . . .

Removing and Installing Panels

10

. . . . . . . . . . . . . . . . .

New or Replacement Line Set

11

. . . . . . . . . . . . . . . . . . .

Brazing Connections

14

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Flushing Line Set and Indoor Coil

17

. . . . . . . . . . . . . . . .

Installing Indoor Metering Device

18

. . . . . . . . . . . . . . . .

Leak Test Line Set and Indoor Coil

19

. . . . . . . . . . . . . . .

Evacuating Line Set and Indoor Coil

20

. . . . . . . . . . . . .

Electrical

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Operation

23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Start-Up and Performance Checklist

24

. . . . . . . . . . . . .

Unit Electrical Diagram and Sequence 
of Operations

25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Servicing Units Void of Charge

27

. . . . . . . . . . . . . . . . . .

Unit Start-Up

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Refrigerant

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

The EL16XC1 air conditioners, which will also be referred
to in this instruction as the outdoor unit, use HFC-410A
refrigerant. This outdoor unit must be installed with a
matching indoor unit and line set as outlined in the 

Lennox

EL16XC1

 

Engineering Handbook

.

This outdoor unit is designed for use in systems that use
one of the following refrigerant metering devices:

Expansion valve (TXV)

Fixed orifice

IMPORTANT:

 Special procedures are required for

cleaning the aluminum coil in this unit. See page 23 in this
manual for information.

Summary of Contents for EL16XC1 Series
































Reviews: