background image

®

AIR CLEANERS/
FILTERS

HEALTHY CLIMATE

®

ELECTRONIC AIR CLEANER

© 2003 Lennox Industries, Inc.

Dallas, Texas USA

INSTALLATION INSTRUCTIONS FOR LENNOX MODELS EAC-14-2, EAC-16-2 AND EAC-20-2

504,812M
06/03

Shut off power at fuse panel before
servicing. Failure to do so could result
in serious personal injury or death.

!

WARNING

ELECTROCUTION HAZARD

Introduction

Please read instructions before installing and using the Elec-
tronic Air Cleaner. This will help you obtain the full benefit from
the Electronic Air Cleaner you have selected. It will also help
you avoid needless service costs that result from causes we
cannot control and cannot cover in our guarantee.

1. Read this manual carefully. Failure to follow these rules

and instructions could cause a malfunction of air cleaner
or unsatisfactory service and could void your warranty.

2. Follow a regular service and maintenance schedule

to ensure efficient operation.

3. Unit must run for one full hour after installation to allow

the collecting cells to reach peak efficiency.

Do not attempt installation of this unit unless you are
familiar with the necessary tools, equipment, utility
connections and potential hazards.

Installation should be performed only by a qualified
service provider.

Failure to do so could result in reduced performance
of the unit, serious personal injury or death.

!

WARNING

Installation of this unit must comply with local
electric codes or other applicable codes.

Review and understand local codes prior to
installation.

!

WARNING

PART NO. 37-6128D

Required Tools

• Tin Snip

• Screwdriver

• Rule or Tape Measure

• Drill

Lennox Industries, Inc.

Dallas, Texas

1-800-9-LENNOX

www.lennox.com

Shipping and Packing List

Package 1 of 1 contains:

1 - EAC Cabinet
2 - Cells
1 - Power Pack
2 - Pre-Filters
1 - Wash Reminder Label
1 - High Voltage Warning Label
1 - Installation Instructions
1 - IAQ Guide and Warranty

Rules for Safe Installation and Operation

CABINET MAY CONTAIN SHARP EDGES.

Use care when servicing unit. Failure to do so could
result in personal injury.

!

CAUTION

EAC-14 (90N80)

 is designed for application with air

handlers which deliver air volumes up to 1600 cfm.

EAC-16 (X1187)

 is designed for application with air

handlers which deliver air volumes up to 2000 cfm.

EAC-20 (90N81)

 is designed for application with air

handlers which deliver air volumes up to 2200 cfm.

Electronic Air Cleaner Models

Persons with respiratory illness or conditions
should consult their physician prior to installing an
electronic air cleaner.

!

WARNING

Sparks which occur during air cleaner operation
may become a source of ignition.

Fire or explosion may occur if flammable vapor or
other combustible products are present while air
cleaner is operating.

Do not operate air cleaner when flammable vapor
or other combustible products are present.

!

WARNING

Summary of Contents for EAC-14-2

































Reviews: