manualshive.com logo in svg

Lennox Core Unit Controller, Setup Manual

Share
Download
Lennox Core Unit Controller Setup Manual Download Page 88

88

16.  Quick Start Guide

CAUTION

Check rooftop unit electrical power for proper voltage and phasing. Check gas train components.

a. 

Turn on unit and dismiss alarm messages as necessary.

b. 

Follow SETUP > INSTALL menu to properly configure unit 

c. 

Be sure unit is in normal operating mode as seen in display (COOLING, HEATING, IDLE, etc).

d. 

To verify operation use SERVICE > TEST menu.

Control Mode

Menu Setup Needed

Tips

THERMOSTAT

(Factory set for 2-stage thermostat)

Check LEDs for signals.

BACnet

SETUP > NETWORK INTEGRATION > NETWORK WIZARD > NETWORK 

TYPE = BACNET MS/TP

• 

Setup information to be verified with 

integrator.

• 

Follow wiring instructions including network 

termination

• 

Remember to set MAC address 0-127

• 

Expert level BACnet service manual available.

LonTalk

SETUP > NETWORK INTEGRATION > NETWORK WIZARD > = LONTALK

• 

Setup information to be verified with 

integrator.

• 

Follow wiring instructions including network 

termination

• 

XIF file available. Neuron ID on sticker.

• 

Expert level LonTalk service manual available.

Damper

SETUP > TEST & BALANCE > DAMPER 

• 

Verify damper minimum positions

• 

Refer to Economizer section of manual for 

more detail

Local Mode

SETUP > NETWORK INTEGRATION >  NETWORK WIZARD > RTU 

STANDALONE

• 

Give unit time to start-up.

• 

Humidity control requires sensor or error code 

7649

Dehumidifier

Dehumidifier setup will be done during the SETUP >INSTALL wizard. It’s the 

last part of that wizard.

• 

Three possible connections, LOCAL 

SENSOR, NETWORK SENSOR and 

REHEAT DI4.

• 

Analog sensor wiring is polarity sensitive

Blower

Change motor torque; see 
SETUP > TEST & BALANCE > BLOWER

• 

Final motor CFM should be set by Test and 

Balance technician

• 

Blower charts are located in the unit 

installation instruction.

Summary of Contents for Core Unit Controller





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands