Lennox Core Unit Controller Setup Manual Download Page 58

Page: 58 / 92

Table 12. CORE Control System Unit Parameters

Control

Parameter

Screen Name

Parameter Short

Description

Control Value

Units

Description

Min.

Default

Max.

140

UNOCC COOL

STPT

Unoccupied

Cooling Set Point

°F

•

Backup unoccupied cooling set

point.

•

Used if the communications link

is lost for 5 minutes between the

CORE Unit Controller and network

control panel. Used only in room

sensor applications.

•

Set point temperature must be

greater than or equal to Parameter

138 plus Parameter 152).

141

AFTERHOUR

OVRRD DLY

After Hours

Override Time

Delay

480

Minutes

•

After hours override timer.

•

Only used on room sensor

applications without a network

control panel.

142

HEAT STAGE

DEADBAND

Heat Stage

Deadband

3.75

°F

•

Heating dead-band. Used only with

CORE Unit Controller room sensor

applications.

•

Dead band must be less than or

equal to Parameter 152 minus

Parameter 143.

143

COOL STAGE

DEADBAND

Cool Stage

Deadband

3.75

°F

•

Cooling dead-band. Used only with

room sensor applications.

•

Dead band must be less than or

equal to Parameter 152 minus

Parameter 142.

144

COOL STAGE1

DIFFER

Cooling Stage 1

Differential

0.5

°F

•

Cooling stage 1 differential. Used

only with room sensor applications.

•

Differential temperature must be

less than or equal to Parameter 145.

145

COOL STAGE2

DIFFER

Cooling Stage 2

Differential

°F

•

Cooling stage 2 differential. Used

only with room sensor applications.

•

Differential temperature must be

greater than or equal to Parameter

144 and less than or equal to

Parameter 146.

146

COOL STAGE3

DIFFER

Cooling Stage 3

Differential

1.5

°F

•

Cooling stage 3 differential. Used

only with room sensor applications.

•

Differential temperature must be

greater than or equal to Parameter

145 and less than or equal to

Parameter 147.

147

COOL STAGE4

DIFFER

Cooling Stage 4

Differential

°F

•

Cooling stage 4 differential. Used

only with room sensor applications.

•

Differential temperature must be

greater than or equal to Parameter

146.

148

HEAT STAGE1

DIFFER

Heating Stage 1

Differential

0.5

°F

•

Heating stage 1 differential. Used

only with room sensor applications.

•

Differential temperature must be

less than or equal to Parameter 149.

149

HEAT STAGE2

DIFFER

Heating Stage 2

Differential

°F

•

Heating stage 2 differential. Used

only with room sensor applications.

•

Differential temperature must be

greater or equal to Parameter 148.

150

HEAT STAGE3

DIFFER

Heating Stage 3

Differential

1.5

°F

•

Heating stage 3 differential

temperature. Used only with room

sensor applications.

•

Differential temperature must be

greater than or equal to Parameter

149.

Summary of Contents for Core Unit Controller





























































































Search results

Summary of Contents for Core Unit Controller

Reviews:

Related manuals for Core Unit Controller

Brands by name

Popular brands

Lennox Core Unit Controller, Setup Manual

Search results

Summary of Contents for Core Unit Controller

Reviews:

Related manuals for Core Unit Controller

Brands by name

Popular brands