8
7. Active Alarms
• The mobile app will display other alarm
information such as time of occurrence, and
troubleshooting information.
• The mobile application will indicate all alarm
information per the active alarm requirements.
• The mobile application will indicate the number of
occurrences of a past alarm in the past thirty (30)
days.
• For alarm details, go to “13. Alarms” on page
37.
8. CORE Service App General Menu + User
Preference
• This screen allows the user to set the temperature
units (ºF or ºC).
• Allows the user to set the screen mode, options
are dark or light modes.
9. CORE Service App RTU Menu
The following options are available under this menu selection:
9.1. Setup
9.1.1. Install
This section includes the following:
• Date and time and the option to use the mobile device
data and time setting.
• RTU Name
•
Model Number (see “Figure 5. Configuration ID 1”) and
serial number. Model , serial and catalog numbers are
located on the RTU nameplate.
•
RTU Information. Configuration ID 1 and 2 can be
entered here. See figures “Figure 5. Configuration ID
1” on page 8 and “Figure 6. Configuration ID 2” on
page 9 for further details.
This section addresses the requirement that specific
configuration information must be completed using the
SETUP / INSTALL feature if a new unit controller was being
installed. Other requirements are the addition of accessories
that were not factory-installed. Model number, configuration
ID 1 and 2, catalog number, serial number and RTU
description are all key items required to be completed for the
system to operate correctly. Running the SETUP / INSTALL
wizard allows the installer to verify that all fields have been
completed as required.
•
Model Number
Type [1, 2, 3]
Electric =
LCM
Gas =
LGM
Tonnage [4, 5, 6]
Efficiency [7]
High Efficiency =
H
Standard Efficiency =
S
Ultra-High Efficiency =
U
[10] Factory Electric or Gas
Heat
See unit nameplate for applicable electric
or gas heat designation.
[11] Design Sequence
1 =
First revision
[12] Voltage
See unit nameplate for
applicable electric voltage
designation.
Refrigerant [8]
HFC-410A =
4
Blower Type [9]
Belt Drive (1 speed) =
B
Direct Drive =
D
EBM MSAV =
E
Mitsubishi MSAV
=
M
Belt Drive (2 speed) =
T
IMPORTANT
: Always refer to the model
information listed on the unit nameplate when
setting these options.
See unit nameplate for
applicable tonnage
designation.
7 8 9 10 11 12
1 2 3 4 5 6
EBM VAV =
P
Mitsubishi VAV =
V
Figure 4. Model Number
CONFIGURATION ID 1
Humiditrol [1]
Not Installed =
N
Humiditrol Installed =
H
Unconfigured =
U
Economizer [2]
Not Installed =
N
Motorized Outdoor Air
Damper Only =
M
Economizer - Temperature =
T
Economizer Global =
G
Economizer - Single
Enthalpy =
S
Economizer - Dual Enthalpy =
D
Unconfigured =
U
Power Exhaust [3]
Not Installed =
N
Single-Stage =
S
Dual-Stage =
D
*Variable Speed Drive =
V
Unconfigured =
U
Power Exhaust Control [4]
Not Installed =
N
Damper Position =
A
*Pressure Switches =
B
*A34 Pressure Sensor =
C
[5] Network Module
N
= Not Installed
B
=
BACnet
L
= LonTalk
[6] Blower Variable
Frequency Drive Bypass
N
= Not Installed
A
=
Automatic Electronic Bypass
M
= Manual Electronic Bypass
U
= Electronic Bypass Field
Un-configured
[7] Smart Air Flow
N
= Not Installed
S
=
Installed with Standard
Economizer
L
= Installed with Low Leak
Economizer
U
= Unconfigured
[8] Outdoor Air Control
N
= No Outdoor Air CFM Control
L
= Outdoor Air Control Installed
with A24 Sensor set for low range.
M
= Outdoor Air Control Installed
with A24 Sensor set for medium
range.
H
= Outdoor Air Control Installed
with A24 Sensor set for high
range.
IMPORTANT
: Always refer to the white sticker titled ORIGINAL FACTORY UNIT CONFIGURATION located inside the control box area.
1 2 3 4 5 6 7 8
Figure 5.
Configuration ID 1
