manualshive.com logo in svg

Lennox Core Unit Controller, Setup Manual

Share
Download
Lennox Core Unit Controller Setup Manual Download Page 61

61

Table 12.  CORE Control System Unit Parameters

Control 

Parameter 

No

Screen Name

Parameter Short 

Description

Control Value

Units

Description

Min.

Default

Max.

169

FAT AUTO 

CHGOVR DLY

Fresh Air 

Tempering 

Automatic 

Changeover 

Delay

15

30

120

Minutes

Fresh Air Heating Control or Fresh Air 

Cooling Control air Tempering auto-

changeover delay.

170

FRESH AIR 

COOL SP

See CORE System Application Guide for further details and to change the fresh air cool (FAC) set point. Modify the 

set point only using the method described in the reference section.

171

FAC STAGE 

DEADBAND

Fresh Air Cooling 

Control Deadband

3

10

15

°F

Fresh Air Cooling stage dead-band.

172

FAC MIN CYCLE 

TIME

Fresh Air Cooling 

Control Cycle 

Time

120

480

1800

Seconds

Fresh Air Cooling minimum cycle time.

173

FAC STAGE 

DIFFER

Fresh Air Cooling 

Control Stage 

Differential

0

2

20

°F

• 

Fresh Air Cooling stage differential 

between stages.

• 

Set to 0 for first stage cooling only 

for Fresh Air Cooling.

174

DACH OCC 

SETPOINT

Discharge Air 

Control Heating 

Occupied Set 

Point

60

110

140

°F

Discharge Air Control Heating set point 

during occupied period.

175

DACH UNOCC 

SETPOINT

Discharge Air 

Control Heating 

Unoccupied Set 

Point

60

95

140

°F

Discharge Air Control Heating set point 

during unoccupied period.

176

DACH STAGE 

DEADBAND

Discharge Air 

Control Heating 

Stage Deadband

5

5

20

°F

Discharge Air Control Heating dead-band.

177

DACH FAH STG 

UP TMR

Discharge Air 

Control Heating 

Stage-Up Time 

Delay

0

180

900

Seconds

Discharge Air Control Heating and Fresh 

Air Heating stage-up time delay.

178

DACH FAH STG 

DN TMR

Discharge Air 

Control Heating 

and Fresh Air 

Heating Control 

Stage-Down Time 

Delay

0

120

600

Seconds

Discharge Air Control Heating and Fresh 

Air Heating stage-down time delay.

179

DACH STAGE 

DIFFER

Discharge Air 

Control Heating 

Stage Differential

2

2

20

°F

Discharge Air Control Heating stage 

differential

180

DACC OCC 

SETPOINT

Discharge Air 

Control Cooling 

Occupied Set 

Point

40

55

80

°F

Discharge Air Control Cooling set point 

during occupied period.

181

DACC UNOCC 

SETPOINT

Discharge Air 

Control Cooling 

Unoccupied Set 

Point

40

65

100

°F

Discharge Air Control Cooling set point 

during unoccupied period.

182

DACC STAGE 

DEADBAND

Discharge Air 

Control Cooling 

Deadband Set 

Point

5

5

20

°F

Discharge Air Control Cooling stage 

dead-band.

183

DACC FAC STG 

UP TMR

Discharge Air 

Control Cooling 

and Fresh Air 

Cooling Stage-Up 

Delay

0

180

900

Seconds

Discharge Air Control Cooling and Fresh 

Air Cooling stage-up delay.

184

DACC FAC STG 

DN TMR

Discharge Air 

Control Cooling 

and Fresh Air 

Cooling Stage-

Down Time Delay

0

120

600

Seconds

Discharge Air Control Cooling and Fresh 

Air Cooling stage-down time delay.

Summary of Contents for Core Unit Controller





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands