Lennox CBX32MV-018/024 Manual Download Page 46 | Manualshive

Page: 46 / 67

background image

Page 46

CBX32MV

3.

Adjust blower speed for cooling. Measure the pressure
drop over the coil to determine the correct blower CFM.
Refer to the unit information service manual for pressure
drop tables and procedure.

4.

Belt Drive Blowers

-

Check belt for wear and proper

tension.

5.

Check all wiring for loose connections.

6.

Check for correct voltage at unit. (blower operating)

7.

Check amp draw on blower motor.

Motor

Nameplate

:_________

Actual

:__________.

Indoor Coil

8.

Clean coil if necessary.

9.

Check connecting lines, joints and coil for evidence of
oil leaks.

10. Check condensate line and clean if necessary.

Cabinet Insulation

IMPORTANT

DAMAGED INSULATION MUST BE REPAIRED OR RE
PLACED before the unit is put back into operation. Insula
tion loses its insulating value when wet, damaged, sepa
rated or torn.

Matt‐ or foil-faced insulation is installed in indoor equipment
to provide a barrier between outside air conditions
(surrounding ambient temperature and humidity) and the
varying conditions inside the unit. If the insulation barrier is
damaged (wet, ripped, torn or separated from the cabinet
walls), the surrounding ambient air will affect the inside
surface temperature of the cabinet. The

temperature/humidity difference between the inside and
outside of the cabinet can cause condensation on the
inside or outside of the cabinet which leads to sheet metal
corrosion and subsequently, component failure.

REPAIRING DAMAGED INSULATION

Areas of condensation on the cabinet surface are an
indication that the insulation is in need of repair.

If the insulation in need of repair is otherwise in good
condition, the insulation should be cut in an X pattern,
peeled open, glued with an appropriate all-purpose glue
and placed back against the cabinet surface, being careful
to not overly compress the insulation so the insulation can
retain its original thickness. If such repair is not possible,
replace the insulation. If using foil‐faced insulation, any cut,
tear, or separations in the insulation surface must be taped
with a similar foil-faced tape.

1. CUT INSULATION IN X PATTERN
2. APPLY GLUE
3. PRESS GLUED TABS AGAINST CABINET

GLUE -make sure there is
full coverage of glue on the
metal or insulation so there
are no areas where air
pockets may form which
can lead to sweating.

Figure 25. Repairing Insulation

«
...
44
45
46
47
48
...
»

Summary of Contents for CBX32MV-018/024




































































Reviews:

No comments

Related manuals for CBX32MV-018/024

Brand: Amana Pages: 82

Brand: Hessaire Pages: 8

Brand: Lasko Pages: 6

Brand: Salton Pages: 12

Brand: mundoclima Pages: 26

Brand: Mestra Pages: 16

Brand: Innova Pages: 24

WAECO VAS 581 001

Brand: Dometic GROUP Pages: 328

Brand: Technibel Pages: 24

Brand: Kaden Pages: 32

Brand: ComfortStar Pages: 43

VRV RXYQ10P7W1B

Brand: Daikin Pages: 139

Brand: ICP Pages: 13

Brand: Momax Pages: 41

Brand: Airgle Pages: 5

Brand: Daewoo Pages: 22

Brand: J&E Hall Pages: 36

Infinity 24ANB6

Brand: Carrier Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands