Leisure Temp LT1000 Page 39 Operation Manual Download | Manualshive

Page: 39 / 45

background image

Page - 36

"Pool / Spa" Button Will Not Work

ISSUE

The "Pool / Spa" button is disabled if the following devices have been configured on the heat pump.
Check with installer if unsure of devices enabled on heat pump.

RESOLUTION

l

A 2-wire external controller.

l

A 3-wire external controller.

l

An external flow switch.

Water Coming From Heat Pump

ISSUE

The water may be normal condensation produced as a by-product of the heat pump's refrigeration
process.

The heat pump can produce up to 8 to 10 gallons (30 to 38 liters) of condensation per hour depending on
the humidity of the ambient air. Determine if the water is condensation or a possible leak.

RESOLUTION

1. Deactivate heat pump, leaving the filter pump on. After several hours, determine if the water is still coming

from the heat pump.

2. If using chlorine or bromine as a pool/spa sanitizer, test the water around the heat pump using a test strip. If

the test strip indicates that chlorine or bromine is present, a leak may exist.

3

-

T

roubl

es

hoot

ing

«
...
37
38
39
40
41
...
»

Summary of Contents for LT1000














































Reviews:

No comments

Related manuals for LT1000

Brand: Radialight Pages: 10

Brand: Vagner Pool Pages: 35

Brand: Carrier Pages: 30

Brand: PAPILLON Pages: 16

jumbo floodfighter

Brand: Davey Pages: 8

Brand: Mueller Pages: 46

Brand: Farelek Pages: 14

Brand: Euromatic Pages: 16

Brand: DAB Pages: 72

Brand: P.Lindberg Pages: 26

Brand: B-TEC Pages: 11

Brand: Enertech Pages: 40

GAU-NFA-HH-150K

Brand: Larson Electronics Pages: 12

Brand: Ultranatura Pages: 24

Brand: salmson Pages: 48

Brand: Defy Pages: 12

Brand: Marta Pages: 12

Brand: SPT Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands