The MIDI capabilities of the Lehle D.Loop SGoS
The
Lehle D.Loop SGoS
is able to receive MIDI program-change commands in
every operation mode.
A lead (adapter) with the following pin assignments must be used to connect other
MIDI-capable devices:
Corresponding leads of various convenient lengths can be ordered from
www.lehle.com.
The
Lehle D.Loop SGoS
transmits on MIDI Channel 15 in Mode 3 (permanent
setting).
Selecting the MIDI reception channel
In its default state, the
Lehle D.Loop SGoS
receives on all MIDI channels
simultaneously (= Omnimode). It is also possible to select a specific channel on which
the L
ehle D.Loop SGoS
is to receive.
The left-hand foot-switch must be pressed before the power-supply connector (7) is
inserted.
The power-supply connector should be inserted while the left-hand foot-switch
remains pressed.
The blue and green LEDs will now flash in sequence. If the left-hand foot-switch is
now released after the first flash of the blue LED, the
Lehle D.Loop SGoS
will only
receive on MIDI Channel 1. Select MIDI Channel 2 by waiting until the green LED
flashes. This is followed by MIDI Channel 3 (blue) and MIDI Channel 4 (green). The
whole procedure can be repeated up to MIDI Channel 16. Omnimodus can be
selected for
Lehle D.Loop SGoS
reception by keeping the left-hand foot-switch
pressed until the green and blue LEDs are on simultaneously.
Switching states can be assigned without restriction to any individual program-change
command using the programming buttons (10), irrespective of the mode selected.
Networking of the Lehle D.Loop SGoS with other Lehle SGoS Switchers
The
Lehle D.Loop SGoS
can be networked with other
Lehle SGoS Switchers
via
the MIDI socket (9). The switchers must be connected using a stereo jack lead for this
purpose:
The
Lehle D.Loop SGoS
and the other
Lehle SGoS Switchers
must first be set to
programmable mode (12).
Switching states on the
Lehle D.Loop SGoS
can be assigned without restriction using
the programming buttons (10) when a
Lehle D.Loop SGoS
foot-switch is pressed.
The
Lehle D.Loop SGoS
simultaneously transmits a MIDI program-change
command to the other
Lehle SGoS Switchers
. Switching states corresponding to this
MIDI program-change command can also be programmed on the other
Lehle SGoS
Switchers
.
The
Lehle SGoS Switcher
receives a MIDI program-change command if a foot-
switch on one of the connected
Lehle SGoS Switchers
is pressed. Any combinations
of Loops or Buffer can, again, be assigned on the
Lehle D.Loop SGoS
for this MIDI
program-change command using the programming button (10).
Several effect loops can, for example, thus be switched simultaneously with one step,
corresponding to a combination of various amps.
Up to three
Lehle D.Loop SGoS
units can be networked with one another.
-4-
Die MIDI Eigenschaften des Lehle D.Loop SGoS
Der
Lehle D.Loop SGoS
empfängt in allen 3 Betriebsmodi MIDI-Programchange
Befehle.
Um andere MIDI-fähige Geräte anzuschließen, muss ein Kabel (Adapter) benutzt werden,
dass folgende Belegung hat:
Passende Kabel mit verschiedenen Kabellängen können unter www.lehle.com bestellt
werden.
Der
Lehle D.Loop SGoS
sendet im Betriebsmodus 3 fest eingestellt auf MIDI-Kanal 15.
MIDI-Empfangskanal festlegen
Im Ausgangszustand empfängt der
Lehle D.Loop SGoS
auf allen MIDI-Kanälen
gleichzeitig (= Omnimodus). Man kann aber auch einen bestimmten Kanal einstellen, auf
dem der
Lehle D.Loop SGoS
empfängt.
Bevor der Stecker für die Stromversorgung (7) eingesteckt wird, muss der linke Fußtaster
gedrückt sein.
Im gedrückten Zustand wird der Stecker für die Stromversorgung eingesteckt.
Jetzt blinken die blaue und grüne LED nacheinander. Lässt man den linken Fußtaster nach
dem ersten Blinken der blauen LED los, empfängt der
Lehle D.Loop SGoS
nur noch auf
MIDI-Kanal 1. Wartet man des Aufleuchten der grünen LED ab, ist der MIDI-Kanal 2
eingestellt. Danach kommt MIDI-Kanal 3 (blau) und MIDI-Kanal 4 (grün). Das Ganze geht
bis MIDI-Kanal 16. Hält man den linken Fußtaster solange gedrückt, bis die grüne und
blaue LED gleichzeitig angehen, empfängt der
Lehle D.Loop SGoS
wieder im
Omnimodus.
Unabhängig vom Betriebsmodus können über die Programmtaster (10) Schaltzustände
jedem einzelnen Programchange frei zugeordnet werden.
Vernetzen des Lehle D.Loop SGoS mit anderen Lehle SGoS Switchern
Der
Lehle D.Loop SGoS
kann mit anderen
Lehle SGoS Switchern
über die MIDI-
Buchse (8) vernetzt werden. Dazu müssen die Switcher mit einem Stereoklinkenkabel
verbunden werden:
Der
Lehle D.Loop SGoS
und die anderen
Lehle SGoS Switcher
müssen erst in den
programmierbaren Modus gebracht werden (12).
Wird ein Fußtaster des
Lehle D.Loop SGoS
betätigt, können dazu Schaltzustände auf
dem
Lehle D.Loop SGoS
mit Hilfe der Programmtaster (10) frei zugeordnet werden. Der
Lehle D.Loop SGoS
gibt dabei gleichzeitig einen MIDI-Programchange Befehl an die
anderen
Lehle SGoS Switcher
ab. Passend zu diesem MIDI-Programchange Befehl
können Schaltzustände auf den anderen
Lehle SGoS Switchern
programmiert werden.
Wird ein Fußtaster auf einem der angeschlossenen
Lehle SGoS Switcher
betätigt,
empfängt der
Lehle D.Loop SGoS
einen MIDI-Programchange Befehl. Zu diesem MIDI-
Programchange Befehl können auf dem
Lehle D.Loop SGoS
wiederum freie
Kombinationen von Amps über die Programmtaster (10) zugeordnet werden.
Damit lassen sich z.B. mehrere Effektloops gleichzeitig mit einem Step passend zu einer
Kombination verschiedener Amps schalten.
Es können bis zu drei
Lehle D.Loop SGoS
miteinander vernetzt werden. Damit allen
über die MDI-Buchse (8) angeschlossenen Geräten klar ist, von welchem Gerät gerade ein
2
5
4
D.Loop
Buffer
Loop A
Loop B
S
R
S
R
Loop A
Loop B
9-20V
D.Loop
Buffer
Loop A
Loop B
S
R
S
R
Loop A
Loop B
9-20V
D.Loop
Buffer
Loop A
Loop B
S
R
S
R
Loop A
Loop B
9-20V
2
5
4
D.Loop
Buffer
Loop A
Loop B
S
R
S
R
Loop A
Loop B
9-20V
D.Loop
Buffer
Loop A
Loop B
S
R
S
R
Loop A
Loop B
9-20V
D.Loop
Buffer
Loop A
Loop B
S
R
S
R
Loop A
Loop B
9-20V