background image

TROUBLESHOOTING

Page 15

F196

APPENDIX A

TROUBLESHOOTING GUIDE

  

        SYMPTOM       

              

        REMEDY       

Lights do not turn on.

- Check if circuit breaker is off.

- Check that wiring to station is correct.
- Check if bulb is burned out.

Lights do not turn off.

- Check that the low level setting is at 0%.

Lights turn on or off suddenly

- Check if that channel is configured as a

during a fade. 

  

  non-dim

All lights fade to full or off  

- Check if the Master Up or Down Button is

when a preset is activated      

  

  stuck.

"Er" appears on the display when   

- Check the All Lock Status (in Configuration

any button is pressed.

 

  Mode).

"Er" appears on the display when   

- Check the Partial Lock Status (in

Store is pressed.

  

  Configuration Mode).

Multiple stations do not track      - Check if the area numbers match (in
each other.

  

  Configuration Mode).

The Solitaire Station front panel

- The front panel will feel warm if the 

feels warm.

  

   lighting load is 1000W or more.  If the

station

   feels unusually hot, have the station

   checked by a qualified technician.

Summary of Contents for SOLITAIRE WBX-4



















Reviews: