LEGRAND Wattstopper DLM LMJA-8 Series Installation Instructions Manual Download Page 18

18

Example of a wireless 4 story building with no more than 40 rooms/common spaces per floor

In larger buildings with more floors and/or more than 300 rooms/spaces, multiple segment managers are used and connected via Ethernet.

WIRING EXAMPLE - WIRELESS

LMJA-8xxx

Primary

LMBR-650

Ethernet

LMBC-650

Wattstopper recommends

a maximum of 

40

 

NB-Switch

 

Secondary

LMBR-650

(Up to 10)

Power Supply 

LMNC

NETWORK SECURITIES

For proper security of the LMJA-8xxx  you MUST implement one of the following options, including but not limited to changing the default user 

name and password at start-up. 

OPTION 1

 

Physical network isolation, achieved by running the lighting control network parallel to and never with interconnection with the customer 

network. This is intended to provide a customer with the ability to physically connect a computer to the lighting control network when needed 

for service or to purchase our Remote Access cellular-based service (RACCESS). 

OPTION 2

 

Virtual network isolation, achieved by placing a secure network gateway between the lighting control network and the customer network. As 

part of this Option 2, state firewall rules are configured on a Wattstopper-provided secure device (RACCESS) or a customer-provided and 

managed device.
 

PLEASE NOTE: 

You 

MUST

 implement one of these two options described above.  Option 1 provides the most secure option, whereas 

the lighting control network never connects with the customer network. Option 2 may not be as secure as Option 1, since it is completely 

dependent on the customer-provided and managed devices for network security.
 

LEGRAND ASSUMES NO RESPONSIBILITY OR LIABILITY FOR A SECURITY FAILURE.  YOUR FAILURE TO IMPLEMENT THESE 

MANDATORY SECURITY STEPS MAY EXPOSE YOU TO LIABILITY IN THE EVENT OF A BREACH.

Summary of Contents for Wattstopper DLM LMJA-8 Series























Reviews: