LEGRAND 5 735 04 Technical Data Manual Download

Page: 9 / 38

9/38

CONTENTS

Cat. No(s).: 5 735 04/05

5 735 12/13

KNX

Arteor 4 and 6 touches glass controls

Technical data sheet: S000090563EN-2

Updated: 07/06/2016

Created : 27/07/2015

11. COMMUNICATION OBJECTS DESCRIPTION (continued)

When standby is active the leds intensity is set to 0% (not adjustable)

Invert standby logic

Yes

This parameter determines the type of logic for active standby

Wake-up

With the "Wake-up" function enabled, when the product is on standby, the first press on any button will light up the LEDs. However, the action will be

sent only after the second press.

11.1.5 Use context information

The contextual information are all the feedback the system provide via the bus and displayed through the LEDs.

The contextual information are displayed each time a push-button is pressed

Context information is not usable, no accessible communication object.

Yes (makes available the contextual information object)

No.

Object name

Function

Size

Flags

4 pushes 73,74,75,76

6 pushes 73,74,75,76,77,78

Channel 1(2,3,4)

ContextInfo

1.010 DP_Start (1 bit )

Context info telegram are received via the group address linked with this object. They are used to inform on event when you push on channel linked.

Parameters

These parameters determine the behaviour of the led after a push when

the “context info is used”.

Setting

Feed back time when Context Info

500 ms

1 second

2 seconds

5 seconds

10 seconds

30 seconds

1 minute

1 min. 30s

2 min.

10 min.

15 min.

30 min.

45 min

1 h

1 h 30

Infinite

Context information led behaviour

Off

Slow blink

Fast blink

Soft blink

Flash 1

Flash 2

Flash 3

Pulse

Summary of Contents for 5 735 04







































Search results

Summary of Contents for 5 735 04

Reviews:

Related manuals for 5 735 04

Brands by name

Popular brands

LEGRAND 5 735 04, Technical Data Manual

Search results

Summary of Contents for 5 735 04

Reviews:

Related manuals for 5 735 04

Brands by name

Popular brands