background image

H03702:02/04

7

C

ONVERSION

 

OF

 C

RIB

 

TO

 T

ODDLER

 B

ED

S

TEP

 9: F

INISHING

 T

OUCHES

.

After completing crib assembly, and after making yourself aware of the

 Warnings, Cautions, Cleaning, Storage, Use 

and

Maintenance

 of crib, store the assembly directions in the plastic pouch which was pre-attached to Spring 

U

U

U

U

U

. For future referral

to assembly directions you will only need to remove them from the plastic pouch. We caution you not to store excess hardware
in plastic pouch as this would be a danger to child if retrieved by him/her.

Check periodically to be sure screws and bolts (fastening devices) remain  tightened as instructed  in each step of
these assembly directions.

Place a purchased mattress on the Spring and crib is ready for use.

)

)

)

)

)

MAINTENANCE OF YOUR LEGACY CRIB: 

Upon completion of assembly be sure screws and bolts (fastening devices)

are tightened securely. A periodic check should be made of  fastening devices and tighten  if needed. Before each usage or assembly,
inspect crib for damaged hardware, loose joints, missing parts or sharp edges. 

DO NOT

 use crib if parts are missing or broken. Ask your

Dealer or  LEGACY (812/ 883-3111) - http://www.childcraftindustries.com  for replacement parts and instructional literature if needed.
Include  Model Identification Number with your request which you recorded on page 1. 

DO

 

NOT

 substitute parts.

 DO NOT

 make any alteration

to this crib.

)

CLEANING INSTRUCTIONS FOR YOUR LEGACY CRIB:

  Mix together a mild solution of gentle dishwashing liquid and

water, apply to crib surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth
then dry all surfaces thoroughly with a soft dry cloth.

 NO

 ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS

SHOULD BE USED TO CLEAN THIS FINE FURNITURE.

)

STORAGE AND USE OF YOUR LEGACY CRIB: 

A printed plastic pouch is attached to the crib spring for the permanent

storage of the assembly directions. After completing the assembly process you are advised to read and be aware of all WARNINGS,
CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in this set of assembly directions and printed on the
plastic pouch attached to crib spring. You will  then place the complete set of assembly directions into the plastic pouch for future referral.
We caution you not to place excess hardware in the plastic pouch as it could present danger to a child if retrieved and it could also puncture
crib mattress. When storing crib use CAUTION as extreme temperature or humidity changes could be harmful. Use CAUTION when a
vaporizer is in use, always aim vapor stream away from crib as well as away from any other wood furniture item.

When converting this crib to a Toddler Bed,

a Guard Rail manufactured by Child Craft Industries, Inc. must be used.

Crib spring will be placed in the lowest position. A separate set of Assembly Directions is provided with the Guard Rail to assist
you through the removal of the dropside and the assembly and installation of the guard rail. When installation of guard rail is
complete, store removed dropside and hardware as instructed. Place both sets of assembly directions in the plastic pouch
attached to the crib spring for future availability. Check periodically to be sure all fastening devices (screws and bolts) remain
tightened as instructed.

SEE WARNINGS ON PAGE 8 OF THESE ASSEMBLY DIRECTIONS.

V

Y

W

X

H

Purchased Mattress

(see size requirements under

CAUTION

 on page 8)

Assembled Crib

(style may vary)

H

Summary of Contents for H03702









Reviews: