background image

 

7.

 

Product Usage 

Function of Action Button: 

 
Door/Window Sensor is not in the Z-Wave network: 

Trigger 

Description 

Power On 

LED will keep on 1 second. 

Short 

press 

time 
(within 1 second) 

1. LED will blink fast for 25 seconds, send Node Info frame. 
2.

 Add for inclusion:

 

 

1.

 

Insert the CR2 battery. 

2.

 

Set the Z-Wave network main controller into learning mode. 

3.

 

Triggering this action button. 

4.

 

If the addition for inclusion is successful, the LED will blink fast and then 
keep  on  3  seconds.  Otherwise,  the  LED  will  blink  25  seconds  and  then 
turn off, in which case you need to repeat the process from step 2. 

 

Door/Window Sensor is in the Z-Wave network: 

Trigger 

Description 

Power On 

Send battery report to associated node 

Short press one time 
(within 1 second) 

1. Led will keep on for 2 seconds 
2.

 Remove for exclusion; 

1.

 

Insert the CR2 battery. 

2.

 

Set the Z-Wave network main controller into exclusion mode. 

3.

 

Triggering this action button. 

If the remove for exclusion is successful, the LED will blink fast and turn 
off. Otherwise, the LED will keep solid for 2 seconds and then turn off, 
in which case you need to repeat the process from step 2. 

Short press 3 time 
(within 1 second) 

1. LED will blink one time; sending wake up notification cc. 
 

Press  and  hold  for  5 
seconds 

Reset Door/Window Sensor to factory Default: 
LED will blink fast for 5 seconds and then keep solid for 3 seconds, after that 
Door/Window  Sensor  will  send  “Device_Reset_Locally”  to  the  main 
controller and exclude from the Z-Wave network. 

Use this procedure only in the event that the network primary controller is missing 
or otherwise inoperable. 

 
Caution: 
 

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 

 

Changes or modifications not expressly approved by the party responsible for compliance could void the 

user's authority to operate the equipment. 

 

Summary of Contents for 7A-SS-AE-H0









Reviews: