background image

Duet

LECTROSONICS, INC.

4

Duet System Overview

The M2 Duet digital IEM system is designed and 

developed with the professional touring, installation, 

theater and broadcast customers in mind. Convention-

al in-ear wireless monitor systems rely on decades-old 

technology: FM transmission with multiplexed, com-

panded audio. The M2 System employs unique digital 

technology to provide ruler-flat frequency response 

from 20 Hz to 15 kHz, wide dynamic range with no 

compression, and maximum channel separation for 

rock-solid stereo imaging or reliable mono opera-

tion with no crosstalk. In addition, the digital audio 

eliminates a compandor and the associated artifacts. 

The result is crystal clear sound and extremely low 

distortion of <0.15% with extremely low latency. The 

transmitter and receiver housings are all-metal for 

maximum durability. 
The system tunes across six standard frequency 

blocks, or from UHF frequencies from 470.100 to 

607.000 MHz (up to 614.375 for the EU version). This 

allows a wide selection of operating frequencies for 

larger systems, and helps avoid interference, even in 

crowded RF environments.
The M2T Digital Half-Rack Transmitter can accept up 

to four analog or digital Dante™ (optional) network 

audio inputs to deliver two stereo or four mono audio 

feeds over two independent RF carriers. A 2-way IR 

port enables quick, trouble-free setup while a large, 

high resolution, backlit LCD and large membrane 

switches provide an intuitive interface that is highly vis-

ible in daylight or dimly lit conditions.
The input connectors are full size XLR/TRS combo 

types for balanced line level analog signals. Input pre-

amp circuits use a special balanced amplifier with very 

high common mode rejection to minimize hum and 

noise. Analog signals are converted to an internal 24-

bit digital format which is then encoded, organized into 

packets, and passed to an RF modulator. The modu-

lated RF signal is filtered before and after amplification 

to suppress out-of-band noise and spurious signals.
The M2R Digital IEM Receiver is a compact, rugged 

body-worn unit providing studio-grade sound qual-

ity for performers or any professionals needing to 

monitor detailed audio wirelessly. The M2R employs 

advanced antenna diversity switching during digital 

packet headers for seamless audio. The headphone 

jack is fed from a high-quality stereo amplifier with 250 

mW available to drive even inefficient headphones or 

earphones to sufficient levels for stage performance or 

other noisy environments. The receiver can select from 

stereo, mono from left or right channels only, or mono 

from both channels, giving the unit flexibility in terms of 

application as an IEM or IFB receiver. An intuitive inter-

face and high resolution, color LCD on the unit provide 

performing artists and audio professionals alike with a 

comfortable and confident user experience.

What is Dante?

Audinate’s patent pending Dante™ technology is a 

flexible Internet Protocol (IP) and Ethernet based 

digital AV network technology that eliminates the many 

bulky cables needed to provide point-to-point wiring for 

analog AV installations.
With Dante, existing infrastructure can be used for 

high performance audio as well as for ordinary control, 

monitoring or business data traffic. Digital networks 

utilize standard IP over Ethernet offering high band-

width capable of transporting hundreds of high quality 

channels over Gigabit Ethernet.
Set-up and configuring the system is made easy as 

well, saving enormous installation costs and long term 

cost of ownership on a digital network. The physical 

connecting point is irrelevant: audio signals can be 

made available anywhere and everywhere. Patching 

and routing now become logical functions configured 

in software, not via physical wired links

Summary of Dante Benefits

• 

Plug-and-play technology – automatic discovery  

        and simple signal routing
• 

Reduced Cost & Complexity- No special skills  

        required to set up audio networking
• 

Sample accurate playback synchronization

• 

Add/remove/rearrange components at will

• 

Deterministic latency throughout the network

• 

Support mixed bit depths and mixed sample  

        rates over one network
• 

Scalable, flexible network topology  supporting a  

        large number of senders and receivers
• 

Supports 1Gbps networks

• 

Supports a single integrated network for audio,  

        video, control, monitoring
• 

Uses inexpensive, off-the-shelf computer  

        networking equipment

Summary of Contents for M2R

































Reviews: