background image

Leaf LT2020E manual 

Page  17  Of  18 

LT2020E: MAIN MATRIX UNIT 

FEATURE 

SPECIFICATION 

INPUTS: DIGITAL-AUDIO/VIDEO 

(20x) HDMI inputs 
VIDEO FORMATS: 
480p,576p,720p50/60,1080i50/60,1080p50/60,HDMI1.
4 Mandatory 3D formats as a minimum.DVI formats. 
AUDIO FORMATS: 
LPCM,AC3,DTS,DD+,DTS-HD (in Multichannel mode) 

ETHERNET PORTS. 

(16x) ETHERNET INPUTS 
100Base-Tx full-duplex Ethernet on all ports 

OUTPUTS: HDBaseT 

(16x) HDBase-T Outputs Uncompressed HD video - 
Supports all formats as in item 1.  
One cable carries: Video, Audio, Ethernet, IR, RS232. 

OUTPUTS: LOCAL AUDIO 

 (16x) 2Ch RCA ANALOG OUTPUTS  
FORMAT: Analog Stereo. Programmable audio delay 
 Sources for these audio outputs may be routed 
independently from HDMI inputs, remote (breakout) or 
local SPDIF inputs. 

INPUTS: LOCAL AUDIO 

(16X) S/PDIF INPUTS 

SYSTEM CONTROL 

(1x) RJ12 Leaf Proprietary Remote control 
(1x) RS232 DB9 IN  
(1x) RS232 DB9 LOOPOUT 
 Bank select and termination selectors. 

INFRA RED REMOTE CONTROL 
THROUGHPUT ONLY 
(No direct control by IR)  

 (16x) DIRECTIONAL IR INPUTs.  Support for: Direct IR, 
IR TX Bug, IR RX Bug. Modulated 38Khz and Envelope. 
 (16x) RJ45 RS-232 PORT for remote control to 
breakouts. 

Up to 115200 Baud.

 

DISPLAY/CONTROL 

Front Panel Touch Screen, enables basic selection and 
display of the connections within the matrix. 

PHYSICAL LAYOUT 

RACK MOUNTABLE (3RU) 
REMOTE ETHERNET AND HDBaseT RJ45s, AND TOUCH 
SCREEN AT FRONT 
ALL OTHER CONNECTORS AT REAR 
RJ12 FOR CONNECTION TO LEAF CONTROLLER 
USER INTERFACE (BASIC): TOUCHSCREEN PANEL.  
STANDARD RACK EARS AND FEET INCLUDED. 

NUMBER OF INPUTS/OUTPUT 

20 /16 

10 

EXPANDABILITY 

Bank Select Switch and Audio Breakaway 

11 

POWER 

60W 5A 12V DC. Consumption depends on resolution 
of distributed video and features enabled. 
120W supply included – Use Leaf Audio supply only. 

12 

DIMENSIONS (W, D, H) 

418(484 incl rack ears) x 290mm, x 133mm(147mm incl 
feet) 

Summary of Contents for LT2020E



















Reviews: