3DM683 Digital Stepping Driver Manual V1.0
Tel: +086 0755-26434369 3 Web Site: www.leadshine.com
Operating Environment and other Specifications
Cooling
Natural Cooling or Forced cooling
Environment
Avoid dust, oil fog and corrosive gases
Ambient Temperature
0
℃
－
50
℃
(32
℉
－
122
℉
)
Humidity
40%RH
－
90%RH
Operating Temperature
70
℃
(158
℉
) Max
Operating Environment
Vibration
5.9m/s
2
Max
Storage Temperature
-20
℃
－
65
℃
(-4
℉
－
149
℉
)
Weight
Approx. 270g (9.5oz)
3. Pin Assignment and Description
The 3DM683 has two connectors, connector P1 for control signals connections, and connector P2 for
power and motor connections. The following tables are brief descriptions of the two connectors.
More detailed descriptions of the pins and related issues are presented in section 4, 5, 9.
Connector P1 Configurations
Pin Function
Details
PUL+
PUL-
Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse
signal, each rising or falling edge active (software configurable); 4-5V when
PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) ,
this input represents clockwise (CW) pulse
，
active both at high level and low
level (software configurable). For reliable response, pulse width should be
longer than 2.5
μ
s. Series connect resistors for current-limiting when +12V or
+24V used. The same as DIR and ENA signals.
DIR+
DIR-
DIR signal: In single-pulse mode, this signal has low/high voltage levels,
representing two directions of motor rotation; in double-pulse mode (software
configurable), this signal is counter-clock (CCW) pulse
，
active both at high
level and low level (software configurable). For reliable motion response, DIR
signal should be ahead of PUL signal by 5
μ
s at least. 4-5V when DIR-HIGH,
0-0.5V when DIR-LOW. Please note that rotation direction is also related to
motor-driver wiring match. Exchanging the connection of two wires for a coil
to the driver will reverse motion direction.
ENA+
ENA-
Enable signal: This signal is used for enabling/disabling the driver. High level
(NPN control signal, PNP and Differential control signals are on the contrary,
namely Low level for enabling.) for enabling the driver and low level for
disabling the driver. Usually left
UNCONNECTED (ENABLED)
.
3DM683 Digital Stepping Driver Manual V1.0
Tel: +086 0755-26434369 4 Web Site: www.leadshine.com
Selecting Active Pulse Edge and Control Signal Mode
The 3DM683 supports PUL/DIR and CW/CCW modes and pulse actives at rising or falling edge. See
more information about these settings in Section 13. Default setting is PUL/DIR mode and rising
edge active (NPN, and PNP control signal is on the contrary).
Connector P2 Configurations
Pin Function
Details
GND
Power Ground
+Vdc
Power supply, 20~60 VDC, Including voltage fluctuation and EMF voltage.
U
Motor phase U
V
Motor phase V
W
Motor phase W
4. Control Signal Connector (P1) Interface
The 3DM683 can accept differential and single-ended inputs (including open-collector and PNP
output). The 3DM683 has 3 optically isolated logic inputs which are located on connector P1 to
accept line driver control signals. These inputs are isolated to minimize or eliminate electrical noises
coupled onto the drive control signals. Recommend use line driver control signals to increase noise
immunity of the driver in interference environments. In the following figures, connections to
open-collector and PNP signals are illustrated.
Figure 2: Connections to open-collector signal (common-anode)
