manualshive.com logo in svg

Leader Evaporator PATRIOT MAX, Manual

Share
Download
Leader Evaporator PATRIOT MAX Manual Download Page 10

 

PATRIOT MAX & STANDARD EVAPORATOR PAN SET      2019 

 

Page:  

10 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.

 

Insert a supplied ¼ - 20 X 3” stainless steel machine screw RH 
through each of the mounting holes in the flue pan located 
above the regulator box connection pipes.  The head of the 
screw will be inside the flue pan. 

 

8.

 

Thread a supplied ¼ - 20 stainless steel nut onto each of the 
machine screws.  Turn the nut towards the flue pan until the 
screw is held into position – do NOT tighten the nut. 

 

9.

 

Thread a second supplied ¼ - 20 nut onto each screw and 
turn the nut until it is approximately 1 ½” down on the 
machine screw. 

10.

 

Align the regulator box connections with the rubber 
connectors on the flue pan.

 

11.

 

Tilt the regulator box top slightly away from the flue 
pan and while straightening the regulator box, slide the 
regulator box connectors into the rubbers connectors 
on the flue pan and the machine screws in the flue pan 
into the mounts on each side of the regulator box. 

12.

 

Thread a supplied ¼ - 20 nut onto each of the machine 
screws and finger tighten against the nut on the 
machine screw.  This will hold the regulator box in 
place. 

13.

 

Press the regulator box into the rubber connectors.  
Ensure the band clamps on each connector are located 
over the connector pipe on the regulator box and face 
screw down then tighten the clamps.

 

Summary of Contents for PATRIOT MAX


























Reviews:

No comments

Brands by name

Popular brands

Load more brands