lawrence doors PBU-150-11 Installation Instructions And Operation Manual Download

Page: 2 / 14

PBU-150-11

09/22

CONTENTS

IMPORTANT INSTALLATION INSTRUCTIONS ......................................................................... 2

SPECIFICATIONS ....................................................................................................................... 3

INSTALLATION INSTRUCTIONS ............................................................................................... 3

WIRING INSTRUCTIONS ............................................................................................................ 4

POWER CONNECTIONS TO DOOR OPERATOR .............................................................. 5

INPUT POWER CONNECTIONS ......................................................................................... 5

BATTERY SPECIFICATION & CONNECTIONS .................................................................. 6

WIRING DIAGRAM ............................................................................................................... 7

TERMINAL CONNECTIONS ................................................................................................ 8

LIGHTS INDICATION ........................................................................................................... 8

OPERATION................................................................................................................................ 9

FRONT PANEL AND SWITCH ............................................................................................. 9

PANEL MENU .................................................................................................................... 10

TURN ON THE OUTPUT POWER ..................................................................................... 11

TURN OFF THE OUTPUT POWER ................................................................................... 11

TROUBLESHOOTING .............................................................................................................. 12

WARNING MESSAGES ..................................................................................................... 12

ERROR MESSAGES .......................................................................................................... 12

CLEARING AN OVERLOAD WARNING MESSAGES ....................................................... 13

CLEARING THE ERROR MESSAGES .............................................................................. 13

MAINTENANCE INSTRUCTIONS ............................................................................................. 13

Summary of Contents for PBU-150-11















Search results

Summary of Contents for PBU-150-11

Reviews:

Related manuals for PBU-150-11

Brands by name

Popular brands

lawrence doors PBU-150-11, Installation Instructions And Operation Manual

Search results

Summary of Contents for PBU-150-11

Reviews:

Related manuals for PBU-150-11

Brands by name

Popular brands