LAWO V_pro8 Installation & Operation Manual Download Page 58

Page: 58 / 109

V1.0/2

V_pro8 Manual

Operation (Web Browser Control)

Video & Audio Processing

The

pro8

provides the following video and audio processing:

Video Processing

Frame Sync

(per channel) - see

SDI In -> FSY & SRC

Variable Delay

(per channel) - see

Delay

Auto Phaser

(per channel) - see

SDI Out -> Delay

Format Conversion

(up to 2 channels;

license

dependent) - see

SDI Out -> Conversion

Colour Correction

(per channel;

dependent) - see

and

Channel ID

and

Timecode Insertion

(per channel) - see

SDI Out -> Ch.ID & Pattern

Audio Processing

Sample Rate Conversion

(for all SDI in & out) - see

SDI In -> FSY & SRC

Variable Delay

(per channel)

- see

Delay

Test tone Generator

(per SDI embedder) - see

SDI Out -> Ch.ID & Pattern

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands