LAWO V_pro8 Installation & Operation Manual Download Page 13

Page: 13 / 109

V_pro8 Manual

V1.0/2

Overview
Licensing

Licensing

The

pro8

comes with a range of licenses designed for different requirements.

Every unit supports:

Status Monitoring

Signal Routing

Frame Sync & SRC

Variable Delay

Channel ID, Timecode & Test Tone Insertion

You may then add the following by purchasing and installing the relevant license. Multiple licenses
may be combined as required:

Colour Correction

- YUV & RGB Colour Correction

Monitoring Package

- Quad split monitoring, Waveform monitoring (YUV & RGB) and the

Vectorscope

Format Conversion 1

- one channel of video format conversion.

Format Conversion 1

- two channels of video format conversion.

In Version 1.0, licenses are pre-installed at the factory.

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands