![background image](http://html1.mh-extra.com/html/lavor/darwin/darwin_manual_3929799022.webp)
EN
22
ASSEMBLY INSTRUCTIONS
See pag. 5
WATER SUPPLY
Water supply collection
WARNING: (symbol) machine not suit-
able for connection to the potable water
mains.
The cleaner can only be connected to the water mains
if the water mains is separated by a backflow preventer.
Make sure that the hose is at least Ø 13mm-1/2 inch and
that it is reinforced.
•
WARNING: Water that has flown through backflow
preventers is considered to be non-potable.
IMPORTANT: Only clean or filtered water should
be used for intake. The delivery of the water intake
tap should be equal to the double of the maximum
pump range.
- Minimum delivery rate: 15 l/ min.
- Maximum intake water temperature: 40°C
- Max inlet water pressure: 1Mpa
Place the cleaner as close to the water supply system
as possible.
Failure to comply with the above conditions causes se-
rious mechanical damage to the pump and the loss of
warranty cover.
PLUG
HOW TO CONNECT THE CORD TO A U.K. PLUG:
IMPORTANT The wires in the mains lead are col-
oured in accordance with the following code:
Blue
Neutral
Brown
Live
Yellow/Green
Earth
Please read the instructions given below before con-
necting the cord to a plug. If in doubt please consult
a qualified electrician. As the colours of the wires in
the mains lead of this appliance may not correspond
with the coloured markings identifying the terminals
in your plug, proceed as follows: The wires that is col-
oured Brown must be connected to the terminal which
is marked with the letter L or coloured Red. The wire
that is coloured Blue must be connected to the termi-
nal wich is marked with the letter N or coloured Black.
Safety points for rewireable or moulded plug: The
mains lead of this appliance may be already fitted with
a BS1363 13A plug.
- If your socket outlet is not suitable for the plug, then
the plug must be removed (cut off if it is a mould-
ed on plug), the flexible cord insulation should be
stripped back as appropriate and a suitable 3 pin
plug fitted.
•
WARNING: Dispose of a plug that has been cut from
the power supply cord, as such a plug is hazardous
if inserted in a live 13A socket outlet elsewhere in
the house. - Should the fuse need to be replaced
an ASTA marked fuse, approved to BS1362, of the
same rating must be used. - Always replace the fuse
cover after fitting a fuse. The plug must NOT be used
if the cover is omitted or lost until a replacement is
obtained. - Make certain that only the correct fuse
cover is used and fitted. - For plugs with detachable
fuse cover the replacement must be the same as the
colour insert in the
base of the plug, or
as directed by the
embossed wording
on the base of the
plug. - If the detach-
able fuse cover is
lost a replacement
may be purchased
from a Service Cen-
tre.
Summary of Contents for Darwin
