Laversab 6300 User Manual Download Page 41 | Manualshive

Page: 41 / 72

background image

34

Select function                ( UP ARROW for functions 1 to 3 )
4.    Execute profile                          5.    Set profiles
6.    Height Correction                     7.    Set  “Ground”
8.    Go to  “Ground”                       9.    Encoder

Once in the correct screen, select a number to go to the desired function. An explanation of
each of the functions is given below.

3.5.0

FUNCTION 0 : IEEE ADDRESS

This function allows the user to enter a valid IEEE-488 address for the 6300. This address is
meaningful only if the “IEEE” option is provided on the 6300. A valid address between 1 and
30 may be entered on the screen shown below.

                        Current  IEEE addr   =   5
                        New IEEE addr         =

.

3.5.1

FUNCTION 1 : VIEW LIMITS

The 6300 checks both the Target values and the Actual values to determine if they are within
specific limits. These limits can be set by the user. To view these limits, you can press the
Function Select key and then choose Function 1 (View Limits) by pressing “1”. The VIEW
LIMITS screen appears as shown below.

                                          VIEW LIMITS
1.  max. knots =    500.0                 4.  max. feet   =    50000
2.  min. knots  =   -200.0                 5.  min. feet     =    -2000
3.  max. mach =  1.000                  6.  max. ft/min.=     6000

To exit from this screen, press CANCEL.

For an explanation of the limits please refer to the “Set Limits” function.

«
...
39
40
41
42
43
...
»

Summary of Contents for 6300









































































Reviews:

No comments

Related manuals for 6300

Brand: Bartlett Pages: 5

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 6

EIP-2000 Series

Brand: ICP DAS USA Pages: 19

Brand: Samson Pages: 20

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

Brand: Fingertips Lab Pages: 15

Brand: Xilinx Pages: 52

Brand: Data Signs Pages: 23

Brand: SOMFY Pages: 112

Brand: SYCLOPE electronic Pages: 40

Brand: Timotion Pages: 10

Brand: Game ready Pages: 24

Brand: XtendLan Pages: 12

Brand: ZBA Pages: 27

Brand: M-system Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands